Abstract:In this paper, dense MAX phase Ti3AlC2 enhanced and toughened TiAl3 matrix composites with mass fractions of 10 similar to 40% were prepared by in-situ reaction via powder metallurgy route which using TiH2, Al and TiC powder as the starting materials. Then, the microstructure and phase structure of the composites were characterized, and the relationship between microstructure, mechanical properties and fracture mechanism was systematically investigated. The results show that the lath-like (micron level) and fine-needle-like (submicron level) re-inforcements Ti3AlC2 are uniformly distributed in TiAl3 matrix. With the increases of mass fraction of re-inforcements, the average grain size of the TiAl3 matrix decreases remarkably from 7.6 mu m to 4.8 mu m, indicating that the reinforcements Ti3AlC2 can effectively refine the matrix grains and plays a good pinning effect on the TiAl3 matrix. The prepared Ti3AlC2/TiAl3 composite with 30% mass fraction exhibits excellent comprehensive mechanical properties: the Vickers hardness, flexural strength, fracture toughness is 575 +/- 5 HV, 470 +/- 18 MPa, and 3.83 +/- 0.05 MPa m(1/2), 14.1%, 174.9% and 117.6% higher than that of the pure TiAl3 matrix, respectively. Both the strengthening and toughening effects are significant. The strengthening mechanism are fine grain strengthening and deformation strengthening, while the toughening mechanism is a synthetic effect in terms of crack deflection, crack bifurcation, grain refinement and stress-induced microcrack. Fracture analysis shows that the fracture mechanism is transgranular (cleavage) fracture.

Mechanical Properties and Microstructure of Al2O3/TiAl in Situ Composites Doped with Cr

Mechanical Properties and Microstructure of Al2o3/Tial in Situ Composites Doped with Cr2o3

In Situal3ti–al2o3 Intermetallic Matrix Composite: Synthesis, Microstructure, and Compressive Behavior

FLEXURAL STRENGTH OF IN-SITU REACTION PROCESSED Al2O3-Al3Ti-Al COMPOSITES

Microstructure and mechanical properties of Al2O 3/TiAl in situ composites doped with Fe2O3

Microstructure and Mechanical Properties of Al<sub>2</sub>O<sub>3</sub>/TiAl <i>In Situ</i> Composites Doped with Fe<sub>2</sub>O<sub>3</sub>

Microstructure and Mechanical Properties of Al<sub>2</sub>O<sub>3</sub>/TiAl <i>in Situ</i> Composites Doped with Fe<sub>2</sub>O<sub>3</sub>

Effect of Cr on Microstructure, Mechanical Properties, and Wear Behavior of in Situ 20 Wt.%al2o3/fe-25Al Composites

Effect of Sintering Temperature on Microstructure and Mechanical Properties of Al2O3/TiAl In-Situ Composites

Microstructure and Mechanical Properties of Ti2AlC-reinforced TiAl Composites

Effect of sintering temperature on microstructure and mechanical properties of Al2O3/TiAl in situ composites

Microstructure and mechanical properties of Ti3(Al,Ga)C2/Al2O3 composites prepared by in situ reactive hot pressing

Reaction mechanism and microstructure evolution of superhigh strength in-situ TiC/Ti composite based on Cr 2 AlC-Ti system

Effect of Cr Contents on Microstructure and Mechanical Properties of ( TiBw + TiCp)/(Ti-4.0Fe-7.3Mo-xCr) Composites

Microstructure and mechanical properties of TiB 2 -Al 2 O 3 composites

Reinforcing and Toughening of Tial Composites by Doping Sm2o3

Mechanical Properties and Microstructure of Al<sub>2</sub>O<sub>3</sub>-Ti<sub>3</sub>SiC<sub>2</sub> Ceramic Composites

Microstructural characterization and mechanical properties of TiAl–Al2Ti4C2–Al2O3–TiC in situ composites by hot-press-aided reaction synthesis

Microstructure and Mechanical Properties of TiB2-Al2O3 Composites

Processing, Microstructural Characterization and Mechanical Properties of in Situ Ti3AlC2/TiAl3 Composite by Hot Pressing

Preparation and toughness mechanism of in-situ Ti<sub>3</sub>AlC<sub>2</sub> enhanced and toughened TiAl<sub>3</sub> matrix composites