Abstract:Background: Various two-stent techniques have been applied to aggressively treat bifurcation lesions as the introduction of drug-eluting stents (DES) and the importance of the bifurcation angle and three-dimensional (3D) structure has come to be recognized. Recent 64 multislice computed tomography (MSCT) technology provides accurate information about the 3D bifurcation geometry of the coronary arteries and with reproducibility. Objectives: The purpose of this study is to disclose the coronary bifurcation angle and 3D structure in humans and elucidate the importance of bifurcation angle for the crush technique using MSCT. Methods: Two hundred and nine patients who were suspected to have angina pectoris and underwent CT angiography using MSCT were examined. The 3D-volume rendering (VR) image was reconstructed by two technicians and was used for the assessment of each coronary bifurcation angles. Results: The average LMT bifurcation angles (\LMT-LAD, \LMT-LCx, \LAD-LCx) were 143 6 138, 121 6 218, and 72 6 228, respectively, the average \LAD-D was 138 6 198, the average \LCxOM was 134 6 238, the average distal RCA bifurcation angles (\RCA-4AV, \RCA-4PD, \4AV-4PD) were 152 6 158, 137 6 208, and 61 6 218, respectively. In addition, a percentage of steep angled bifurcation (<1108) was significantly higher in the LMT (26%) than in other bifurcations (P < 0.05). Conclusions: LMT bifurcation has been shown to have a higher rate of steep angled bifurcation in humans, it is therefore necessary to take the bifurcation angle into consideration in the case of LMT stenting. These data suggest that a bifurcation study using MSCT can clarify the 3D structure of coronary bifurcation and may provide useful information for bifurcation stenting. ' 2009 Wiley-Liss, Inc.

Development of Nanomachining Mechanism Based on Molecular Dynamics Simulation

Molecular Dynamics Simulation of Micro Cutting Process of Abrasive Wear

Study on Mechanism for Material Removal and Surface Generation by Molecular Dynamics Simulation in Abrasive Processes

Molecular Dynamics Simulation on the Mechanism of Nanometric Machining of Single-Crystal Silicon

Molecular dynamics simulation on nanoindentation response of a copper workpiece

0701 Molecular Dynamics Simulation of Nano-Contact Between a Diamond Cutting Tool and a Copper Surface

Molecular Dynamics Analysis Micro-Mechanism Of Ductile Machining Single Crystal Silicon By Means Of Nanometric Cutting Technology

Molecular Dynamics Simulation on Cutting Mechanism in the Hybrid Machining Process of Single-Crystal Silicon

Molecular dynamics simulation of the influence of nanocutting parameters on microstructure of AISI M2

Molecular dynamics simulation study of interaction mechanism between grain boundaries and subgrain boundaries in nano-cutting

Investigation of nanomachining-induced plastic behavior using machine learning-assisted high-throughput molecular dynamics simulations

NON-INVASIVE ANGIOGRAPHY Original Studies The Bifurcation Study Using 64 MultiSlice Computed Tomography

Investigation on nano-grinding process of GaN using molecular dynamics simulation: Nano-grinding parameters effect

Atomic simulation study on the effect of defects on nano-cutting mechanism of single crystal copper

Molecular Dynamics Simulation of Multi-Groove Nano-Milling

Progress of Molecular Dynamics Studies on Nanotribology

Modelling and experimental investigation on nanometric cutting of monocrystalline silicon

Molecular Dynamics Study of Nano-Grinding Behavior for Silicon Wafer Workpieces with Nanoscale Roughness Under Diamond Abrasive Rotation and Translation

Material removal mechanism of FCC single-crystalline materials at nano-scales: Chip removal & ploughing

Molecular Modeling of the Mechanical Effect in the Chemical Mechanical Polishing Process

Nanocutting mechanisms of Cu50Zr50 amorphous alloy: A molecular dynamics simulation