Abstract:A series of experiments has been conducted to investigate the tribological properties of a TiN film sliding against GCr15 steel balls in ambient air, low vacuum and high vacuum environments. Various friction loads and sliding velocities were also applied. The TiN film displays a steady-state friction stage after the running-in stage in all the above environments, while the durations of running-in stages are different. The steady-state friction coefficients of the TiN film were around 0.56 in ambient air and 0.3 in the high vacuum environment (1 × 10−5 mbar). In the low vacuum (1 × 10−2 mbar) environment, a low friction coefficient (around 0.19) was attained for all the friction tests on TiN film, irrespective of the applied load and sliding velocity. In the meantime, it was noticed that the applied loads and the sliding velocities would change the duration of the running-in stage before reaching the low friction coefficient. It is revealed by the analysis of wear tracks that the metal oxides induced by the tribo-chemical effect at the friction interface play an important role in affecting the tribological behaviors of the TiN films in different environments. The Raman results show that the main component of the metal oxides is hematite (α-Fe2O3), and the amount of iron oxide is related to the friction environment. The composition and quantity of iron oxides produced by the interfacial tribo-chemical effect affect the tribological behavior. The results also show that the mechanical wear process at the friction interface displays a polishing effect, which would reduce the surface roughness. The mechanical wear performance varies under different loads and velocities. The tribological tests results indicate that the interfacial tribo-chemical effect and mechanical wear process should be considered together rather than individually to interpret the tribological behaviors of TiN films in different environments.

Correlated Extended X-ray Absorption Fine Structure and Transmission Electron Microscopy Studies the Microstructure of Low Friction Ti–C–N Films

Tribological Properties of Ta‐C‐N and Ta‐N Thin Films

Influence of Carbon Contents on the Structure and Tribocorrosion Properties of Tisicn Coatings on Ti6al4v

The microstructure and mechanical properties of Ti(CoCr)N films produced by DC magnetron sputtering

Microstructure, mechanical and tribological properties of TiCN nanocomposite films deposited by DC magnetron sputtering

Microstructure, Mechanical, and Tribological Properties of Cr-Ti-Si-N Coatings

Tribological and mechanical behaviors of TiN/CNx multilayer films deposited by magnetron sputtering

Influence of film structure on the microstructure and properties of TiAlN coatings on Al-Si alloys

Influence of Interfacial Tribo-Chemical and Mechanical Effect on Tribological Behaviors of TiN Film in Different Environments

Structural and Mechanical Properties of TaN/a-CNx Multilayer Films

Fractography, microstructure and thermal stability of multilayer CN x/TiN composite films prepared by DC reactive magnetron sputtering

Preparation and tribological behavior of TiN/a-C composite films deposited by DC magnetron sputtering

Investigations on microstructure, mechanical and tribological properties of TiN coatings deposited on three different tool materials

Study on the growth and wear characters of CVD coating deposited on Ti(C, N)-based cermets with adding different C/N ratios of Ti(C, N) powders

Influence of Nitrogen Partial Pressure on Structure, Mechanical and Tribological Properties of TaCN Coatings

Microstructure and Tribological Behavior of Pulsed Laser Deposited A-Cnx Films

Electron-Spectroscopy Study Of Amorphous Cn : Ti Films

Microstructure and Tribological Properties of Ti-contained Amorphous Carbon Film Deposited by DC Magnetron Sputtering

The influence of carbon content on the microstructure, mechanical and frictional property of chromium carbon nitride composite films

Microstructure and Tribological Properties of Multilayered ZrCrW(C)N Coatings Fabricated by Cathodic Vacuum-Arc Deposition

Microstructure, mechanical and tribological properties Of A-C/A-C:Ti nanomultilayer film