Abstract:High-entropy alloys (HEAs) of AlxCoCrFeNi (x = 0.2, 0.5, and 1) were created using the spark plasma sintering (SPS) method in conjunction with an aerosolized powder. Their microstructure and phase constituents were characterized by X-ray diffractometry, scanning electron microscopy, and projection electron microscopy. The tensile properties, hardness, compactness, and damping properties were also tested. The results showed that the crystal structure of AlxCoCrFeNi HEAs changed significantly with the Al content, from the original single face-centered cubic FCC phase (Al0.2CoCrFeNi) to an FCC + BCC + B2 structure (Al0.5CoCrFeNi), and then to FCC + BCC + B2 + Sigma (σ) phase structures (AlCoCrFeNi). Twin crystals with FCC structure were also observed in the TEM of AlCoCrFeNi. A chemical composition analysis showed that the crystal structure transformation was related to the segregation caused by the increase of Al element content. The hardness of the AlxCoCrFeNi HEAs increased with the Al content, and the hardness of AlCoCrFeNi reached the highest value of 585.4 HV. The tensile properties of the alloy showed a trend of increasing and then decreasing values with the increase in Al content. The yield strength, ultimate tensile strength, and elongation of the Al0.5CoCrFeNi alloy reached the highest values of 557.7 MPa, 954.4 MPa, and 32.2%, respectively. Moreover, the fracture mechanism of the Al0.2CoCrFeNi and Al0.5CoCrFeNi alloys was that of a typical ductile fracture, while for the AlCoCrFeNi alloy, it was that of a cleavage fracture. The compactness of the alloy increased with the Al content. The combination of the FCC + BCC + B2 phase resulted in the damping capacity of Al0.5CoCrFeNi alloy reaching 0.018 at the corresponding strain amplitude of 6 × 10−4.

Alloying Behavior and Novel Properties of CoCrFeNiMn High-Entropy Alloy Fabricated by Mechanical Alloying and Spark Plasma Sintering

Microstructure and mechanical properties of CoCrFeNiTa high entropy alloy prepared by mechanical alloying and spark plasma sintering

Microstructure and Magnetic Characteristics of AlCrCuFeNiTi High-Entropy Alloy Prepared by Mechanical Alloying Followed by Spark Plasma Sintering

Structure and properties of Fe40Mn20Cr20Ti10Al10 high-entropy alloy fabricated by mechanical alloying and spark plasma sintering

Microstructure and mechanical properties of Al-Fe-Co-Cr-Ni high entropy alloy fabricated via powder extrusion

Microstructure and Properties of NiCoCrAlTi High Entropy Alloy Prepared Using MA-SPS Technique

Hot cracking, crystal orientation and compressive strength of an equimolar CoCrFeMnNi high-entropy alloy printed by selective laser melting

Synthesis and Characterization Study of Al10Cr25Co20Ni25Fe20 High-Entropy Alloy Powders through Mechanical Alloying

Microstructure, Mechanical Properties, and Damping Capacity of AlxCoCrFeNi High-Entropy Alloys Prepared by Spark Plasma Sintering

Microstructure and mechanical properties of a high entropy alloy with a eutectic composition (AlCoCrFeNi2.1) synthesized by mechanical alloying and spark plasma sintering

Alloying behavior and characterization of (CoCrFeNiMn)90M10 (M=Al, Hf) high-entropy materials fabricated by mechanical alloying

Strengthening and deformation mechanism of high-strength CrMnFeCoNi high entropy alloy prepared by powder metallurgy

A novel and sustainable method to develop non-equiatomic CoCrFeNiMox high entropy alloys via spark plasma sintering using commercial commodity powders and evaluation of its mechanical behaviour

Nano-Structure Evolution and Mechanical Properties of AlxCoCrFeNi2.1 (x = 0, 0.3, 0.7, 1.0, 1.3) High-Entropy Alloy Prepared by Mechanical Alloying and Spark Plasma Sintering

Microstructure characterization and phase evolution of equiatomic AlCoMoFeNi high entropy alloy synthesized by mechanical alloying

Alloying Behavior and Properties of FeSiBAlNiCox High Entropy Alloys Fabricated by Mechanical Alloying and Spark Plasma Sintering

Microstructure of and mechanical properties of an as-cast fine-grain dual-phase Fe-based high entropy alloy formed via solid-state phase transformation

Fine tuning in-sync the mechanical and magnetic properties of FeCoNiAl0.25Mn0.25 high-entropy alloy through cold rolling and annealing treatment

In-situ synthesis of CoCrFeMnNi high-entropy alloy by selective laser melting

Microstructure and mechanical properties of AlCoCrFeMnNi HEAs fabricated by selective laser melting

Magnetic and mechanical properties of nanotwin SiO 2 -FeCoNi(AlSi) 0.4 high entropy alloy prepared by mechanical alloying and spark plasma sintering