Abstract:In this study, transmission electron microscopy (TEM) and atom probe tomography (APT) were utilized to investigate the microstructure and phases in an Fe25Ni25Co25Ti15Al10 high-entropy alloy (HEA) prepared by mechanical alloying (MA) and spark plasma sintering (SPS). The bulk Fe25Ni25Co25Ti15Al10 HEA was characterized by a high tensile strength of 2.52 GPa and contained a minor bcc phase (∼17.7 vol%), together with a primary fcc phase (∼82.3 vol%) containing hierarchical nanoprecipitates. The bcc phase was a B2-type NiAl phase that contained substantial amounts of Co, Ti and Fe; it also exhibited Fe and Co rich nanoprecipitates with an average diameter of 1.11 ± 0.33 nm. The fcc phase consisted of a γ Fe-(Co,Ni)-based solid-solution matrix (A1), and coherent primary γ’ (Ni,Co)3-(Ti,Al)-based intermetallic precipitates (L12). A1 structured secondary γ* precipitates were found coherently embedded in the L12-γ′ precipitates. We propose that the formation of the secondary γ* precipitates was largely driven by the unique chemical composition of the γ’ precipitates which accommodate substantial amounts of Fe, Al and Ti, coupled with the nonequilibrium processing route used in our studies. Surprisingly, a novel type of Al–Ti–O oxide was identified via APT. A Ti(C,N) compound containing ∼9.19 at.% N and ∼12.27 at.% Ni was also detected by APT, rather than a simple TiC. Our analysis suggests that the Al–Ti–O oxide likely formed during MA, whereas the Ti(C,N) phase formed during sintering. In addition, a CALPHAD (Calculation of Phase Diagrams) approach was utilized to assist in understanding the underlying phase formation mechanisms. The notable high strength of 2.52 GPa in the Fe25Ni25Co25Ti15Al10 HEA support the hypothesis that phase formation mechanisms play an important role in the mechanical performance of HEAs fabricated by powder metallurgy.

Synthesis and Characterization Study of Al10Cr25Co20Ni25Fe20 High-Entropy Alloy Powders through Mechanical Alloying

Microstructure and mechanical properties of CoCrFeNiTa high entropy alloy prepared by mechanical alloying and spark plasma sintering

Structure and properties of Fe40Mn20Cr20Ti10Al10 high-entropy alloy fabricated by mechanical alloying and spark plasma sintering

Nanostructured Al–Ti–Fe–Mn–Ni High-Entropy Alloy by Mechanical Alloying: Synthesis and Characterization

Microstructure and Properties of NiCoCrAlTi High Entropy Alloy Prepared Using MA-SPS Technique

Synthesis and Phase Evolution of a Nanocrystalline FexCrNiAl (x = 1.0, 0.5, 0.25) High-Entropy Alloys by Mechanical Alloying

Microstructure and Magnetic Characteristics of AlCrCuFeNiTi High-Entropy Alloy Prepared by Mechanical Alloying Followed by Spark Plasma Sintering

A New Type of High Entropy Alloy Composite Fe18Ni23Co25Cr21Mo8WNb3C2 Prepared by Mechanical Alloying and Hot Pressing Sintering

Microstructure and mechanical properties of Al-Fe-Co-Cr-Ni high entropy alloy fabricated via powder extrusion

Alloying behavior and characterization of (CoCrFeNiMn)90M10 (M=Al, Hf) high-entropy materials fabricated by mechanical alloying

Microstructure characterization and phase evolution of equiatomic AlCoMoFeNi high entropy alloy synthesized by mechanical alloying

Phase prediction, microstructure, and mechanical properties of spark plasma sintered Ni–Al–Ti–Mn–Co–Fe–Cr high entropy alloys

Microstructure, Mechanical Properties, and Damping Capacity of AlxCoCrFeNi High-Entropy Alloys Prepared by Spark Plasma Sintering

Microstructural Study of CrNiCoFeMn High Entropy Alloy Obtained by Selective Laser Melting

Microstructural evolution of CrCuFeNiZn nanocrystalline high entropy alloy prepared by mechanical alloying

Macrostructure, Microstructure, and Mechanical Properties of Al0.2CoCrFeNi High-Entropy Alloy Produced by Vacuum Induction Melting

Structural and Comprehensive Performance of CoCrFeMnNi High-Entropy Alloys via Fast Hot-Pressed Sintering: Effect of Sintering Temperature

Development of a large size FCC high-entropy alloy with excellent mechanical properties

Manufacturing of Ni-Co-Fe-Cr-Al-Ti High-Entropy Alloy Using Directed Energy Deposition and Evaluation of Its Microstructure, Tensile Strength, and Microhardness

Atom probe tomography study of an Fe25Ni25Co25Ti15Al10 high-entropy alloy fabricated by powder metallurgy

Effect of Aluminum Addition on the Microstructure, Magnetic, and Mechanical Properties of FeCrCoNiMn High-Entropy Alloy