Abstract:In this study, transmission electron microscopy (TEM) and atom probe tomography (APT) were utilized to investigate the microstructure and phases in an Fe25Ni25Co25Ti15Al10 high-entropy alloy (HEA) prepared by mechanical alloying (MA) and spark plasma sintering (SPS). The bulk Fe25Ni25Co25Ti15Al10 HEA was characterized by a high tensile strength of 2.52 GPa and contained a minor bcc phase (∼17.7 vol%), together with a primary fcc phase (∼82.3 vol%) containing hierarchical nanoprecipitates. The bcc phase was a B2-type NiAl phase that contained substantial amounts of Co, Ti and Fe; it also exhibited Fe and Co rich nanoprecipitates with an average diameter of 1.11 ± 0.33 nm. The fcc phase consisted of a γ Fe-(Co,Ni)-based solid-solution matrix (A1), and coherent primary γ’ (Ni,Co)3-(Ti,Al)-based intermetallic precipitates (L12). A1 structured secondary γ* precipitates were found coherently embedded in the L12-γ′ precipitates. We propose that the formation of the secondary γ* precipitates was largely driven by the unique chemical composition of the γ’ precipitates which accommodate substantial amounts of Fe, Al and Ti, coupled with the nonequilibrium processing route used in our studies. Surprisingly, a novel type of Al–Ti–O oxide was identified via APT. A Ti(C,N) compound containing ∼9.19 at.% N and ∼12.27 at.% Ni was also detected by APT, rather than a simple TiC. Our analysis suggests that the Al–Ti–O oxide likely formed during MA, whereas the Ti(C,N) phase formed during sintering. In addition, a CALPHAD (Calculation of Phase Diagrams) approach was utilized to assist in understanding the underlying phase formation mechanisms. The notable high strength of 2.52 GPa in the Fe25Ni25Co25Ti15Al10 HEA support the hypothesis that phase formation mechanisms play an important role in the mechanical performance of HEAs fabricated by powder metallurgy.

Structure and properties of Fe40Mn20Cr20Ti10Al10 high-entropy alloy fabricated by mechanical alloying and spark plasma sintering

Microstructure and mechanical properties of CoCrFeNiTa high entropy alloy prepared by mechanical alloying and spark plasma sintering

Nanostructured Al–Ti–Fe–Mn–Ni High-Entropy Alloy by Mechanical Alloying: Synthesis and Characterization

Synthesis and Characterization Study of Al10Cr25Co20Ni25Fe20 High-Entropy Alloy Powders through Mechanical Alloying

Microstructure and Properties of NiCoCrAlTi High Entropy Alloy Prepared Using MA-SPS Technique

Microstructure and mechanical properties of Al-Fe-Co-Cr-Ni high entropy alloy fabricated via powder extrusion

Microstructure and Magnetic Characteristics of AlCrCuFeNiTi High-Entropy Alloy Prepared by Mechanical Alloying Followed by Spark Plasma Sintering

Microstructure of and mechanical properties of an as-cast fine-grain dual-phase Fe-based high entropy alloy formed via solid-state phase transformation

Phase prediction, microstructure, and mechanical properties of spark plasma sintered Ni–Al–Ti–Mn–Co–Fe–Cr high entropy alloys

Atom probe tomography study of an Fe25Ni25Co25Ti15Al10 high-entropy alloy fabricated by powder metallurgy

Microstructure, Thermal Properties, and Corrosion Behaviors of FeSiBAlNi Alloy Fabricated by Mechanical Alloying and Spark Plasma Sintering

Realizing strength-ductility combination of Fe3.5Ni3.5Cr2MnAl0.7 high-entropy alloy via coherent dual-phase structure

Structure and Properties of a High-Entropy Ti-Zr-Hf-Ni-Co-Cu Alloy Obtained by Mechanical Alloying and Spark Plasma Sintering

Microstructure and mechanical properties of oxide dispersion strengthened FeNiMnCr high-entropy alloy fabricated by spark plasma sintering

A novel and sustainable method to develop non-equiatomic CoCrFeNiMox high entropy alloys via spark plasma sintering using commercial commodity powders and evaluation of its mechanical behaviour

Development of a large size FCC high-entropy alloy with excellent mechanical properties

Electron beam melting of (FeCoNi)86Al7Ti7 high-entropy alloy

Heterogeneous Microstructure and Tensile Properties of Fe50Mn30Co10Cr10 Metastable High-Entropy Alloy

Alloying Behavior and Properties of FeSiBAlNiCox High Entropy Alloys Fabricated by Mechanical Alloying and Spark Plasma Sintering

Microstructure, Mechanical Properties, and Damping Capacity of AlxCoCrFeNi High-Entropy Alloys Prepared by Spark Plasma Sintering

Microstructure and Properties of a Co-Free Fe50mn27ni10cr13 High Entropy Alloy