Abstract:This study provides a new idea for the design of an advanced foaming agent with soybean residue protein (SRP) as a potential protein source. In order to achieve the most effective foaming performance, we employed the novel approach of response surface methodology (RSM) to improve important process parameters in a hot-alkali experiment. The experimental results showed that the optimum reaction parameters of pH and temperature were pH 10.2 and 50.5 °C, respectively, which, when continued for 3 h, led to the highest foaming property of the SRP foaming agent (486 mL). Based on the scheme, we also designed an experiment whereby we incorporated 1.0g/L FS-50 into the SRP foaming agent (SRP-50) to achieve higher foaming capacity compared with the commercial foaming agent. This foaming agent was cheaper than commercial vegetable protein foaming agents (12 USD/L) at 0.258 USD/L. Meanwhile, the properties of foam concrete prepared using SRP-50 were studied in comparison with a commercial vegetable protein foaming agent (PS). The results demonstrated that the foam prepared using SRP-50 had better stability, and the displacement of the foam decreased by 10% after 10 min. During the curing period, the foam concrete possesseda compressive strength of 5.72 MPa after 28 days, which was an increase from 2.95 MPa before. The aperture of the foam ranged from 100 to 500 μm with the percentage increasing up to 71.5%, which indicated narrower pore-size distribution and finer pore size. In addition, the shrinkage of the foam concrete was also improved. These findings not only achieve the utilization of waste but also provide a new source for protein foaming agents.

Protein Foaming Method to Prepare Si3N4 Foams by Using a Mixture of Egg White Protein and Whey Protein Isolate

Preparation, Characterization, and Foaming Properties of Soy Protein Nanoparticles by the Cross-Linking Reaction Induced by Microbial Transglutaminase

Enhancing Foam Stability with Β-Lactoglobulin Nanoparticles: Insights into Molecular-Level Interplay and Stabilization Mechanism

Comparative Study on Foaming Properties of Egg White with Yolk Fractions and Their Hydrolysates

Effect of Xanthoceras sorbifolium bunge leaves saponins on the foaming properties of whey protein isolate at varying pHs: Correlation between interface, rheology, and foaming characteristics

Formation of hierarchical Si3N4 foams by protein-based gelcasting and chemical vapor infiltration

Preparation of Si3N4 Foam Ceramics Using Short-Chain Amphiphile

Foaming and Physicochemical Properties of Commercial Protein Ingredients Used for Infant Formula Formulation

Effects of incorporating different kinds of peptides on the foaming properties of egg white powder

Study on particle-stabilized Si3N4 ceramic foams

Preparation of Si 3N 4 foam ceramics with nest-like cell structure by particle-stabilized foams

Inner Voids of Octavinyl Polyhedral Oligomeric Silsesquioxane Acting as Cell Embryos for Polymer Foaming

Pickering Foam Stabilized by Diacylglycerol-Based Solid Lipid Nanoparticles: Effect of Protein Modification

Pore Structure Control of Si3n4 Ceramics Based on Particle-Stabilized Foams

Preparation and Application of Foaming Agent Based on the Compound System of Short-Chain Fluorocarbon and Soybean Residue Protein

Fabrication of in-situ self-reinforced Si3N4 ceramic foams for high-temperature thermal insulation by protein foaming method

A Novel Method of Strong and Tough Si3N4 Ceramic from the Particle‐stabilized Foam

Effect of Corn Starch Granules on Stabilizing the Foam Structure of Ultrasonically Modified Whey Isolate Protein

Polyphenol improve the foaming properties of soybean isolate protein: Structural, physicochemical property changes and application in angel cake

Factors affecting the microstructure of a fine ceramic foam

Ultralight Silicon Nitride Ceramic Foams from Foams Stabilized by Partially Hydrophobic Particles