Abstract:Improving the hot workability and reducing the processing cost are critical steps to expanding the application of TiC/Ti-6Al-4V composites. This study employed melt hydrogenation to fabricate TiC/Ti-6Al-4V composites under a mixed atmosphere of hydrogen and argon. Experimental results indicated that hydrogen had an obvious influence on the growth and morphology of eutectic TiC particles, and the size of eutectic TiC and primary β grains was significantly increased. As a result, large-sized eutectic TiC was distributed along the grain boundaries of primary β grains. Hot compression results showed that the peak flowing stress of composites was reduced by hydrogen, which resulted in an improvement of hot workability, especially in the (α + β) phase region, and the best results were obtained at 900 °C/0.01 s−1, at which the peak stress decreased from 241 ± 9 to 190 ± 8 MPa (a decrease of 21.2%). Inspection of the microstructure after hot compression showed that hydrogen improved the proportion of DRX grains from ~62.7% to ~83.2%, and hydrogen also decreased the density of dislocations, which were attributed to hydrogen accelerating atomic diffusion. Enhanced hot workability resulted from hydrogen atoms decreasing the atomic bonding force of the titanium matrix, hydrogen reducing the β/(α + β) transition temperature, the higher proportion of DRX, and the higher mobility of dislocations. It is expected that the findings of this study may support the development of a simple and efficient method to reduce the processing cost of TiC/Ti-6Al-4V composites.

Phase Transformations and Formation of Ultra-Fine Microstructure During Hydrogen Sintering and Phase Transformation (HSPT) Processing of Ti-6Al-4V

An Experimental Study of the (ti–6al–4v)–xh Phase Diagram Using in Situ Synchrotron XRD and TGA/DSC Techniques

Investigating phase transformation, densification and diffusion mechanism of TiH 2 powder to achieve a high ductile Ti6Al4V alloy

Phase Transformation, Microstructural Evolution and Tensile Properties of a TiH2-Based Powder Metallurgy Pure Titanium

Size Dependent Phase Transformation in Atomized TiAl Powders

Microstructural Modification and Mechanical Improvement of Ultrafine-Grained Ti Alloy Through Electron Wind Force: an Innovative Approach

Improving the Mechanical Processing of Titanium by Hydrogen Doping: A First-Principles Study

Effect of hydrogen on the structural and phase state and defect structure of titanium alloy

Phase Structure and Hydrogen Storage Properties of Ti17cr23v55-Xzr5fex (X=11 Similar to 16) Alloys

Influence of Heat Treatment on the Microstructure and Hydrogen Storage Properties of Ti10V77Cr6Fe6Zr Alloy

The effect of hydrogen on the grain refinement and mechanisms for Ti6Al4V alloys during laser melting deposition

Hydrogen promoted Ti 3 Al precipitation during Ti-6Al-4V martensite tempering

Evolution of the Structural-Phase State of a Titanium Alloy of the System Ti–Al–V–Mo During Formation of an Ultrafine-Grained Structure Using Reversible Hydrogenaтion

Phase transformation mechanisms, microstructural characteristics and mechanical performances of an additively manufactured Ti-6Al-4V alloy under dual-stage heat treatment

Deciphering Hydrogen Embrittlement Mechanisms in Ti6Al4V Alloy: Role of Solute Hydrogen and Hydride Phase

Hydrogen concentration dependence of phase transformation and microstructure modification in metastable titanium alloy β-21S

Effect of hydrogen on hot deformation behavior and microstructure evolution of Ti65 alloy

Novel transformation pathway and heterogeneous precipitate microstructure in Ti-alloys

Microstructure and Mechanical Properties of Hydrogenated-Dehydrogenated Ti-6Al-4V Alloy

Characterizing solute hydrogen and hydrides in pure and alloyed titanium at the atomic scale

Microstructure Evolution and Enhanced Hot Workability of TiC/Ti-6Al-4V Composites Fabricated by Melt Hydrogenation