Abstract:The limited plasticity and poor formability of TiAl alloys constitute primary constraints on their widespread applicability. In this regard, an innovative forming method is proposed, characterized by the direct forging of unconsolidated pre-alloyed Ti–48Al–2Cr–2Nb powders. In this procedure, spherical powders with a broad particle size distribution are pre-encapsulated and subjected to vacuumed treatment, followed by direct high-temperature forging to attain the final desired shape. Throughout the process, the powders undergo pre-heating to various forming temperatures and are forged at different speeds, enabling a comparative analysis of the effect of forging temperature and speed on densification and the microstructural characteristics of the forged billet. Experimental results indicate that the powders can be nearly fully densified when direct forging is conducted within the α-phase region. By combining the finite element modeling and microstructural characterization, three mechanisms dominating the consolidation process of powders are revealed. Initial particle clustering and spatial rearrangement predominantly occur during the early deformation stage, enhancing densification. Subsequent fragmentation of particles, induced by severe plastic deformation, governs the entire deformation process, leading to the elimination of the prior particle boundaries and substantial densification improvement. The closure of the micrometer-scale voids is controlled by high-temperature diffusion and creep, which plays a pivotal role in weakening the detrimental effect of micro defects on mechanical properties. The above mechanisms act alternately or simultaneously, resulting in a homogeneous microstructure composed of α2+γ lamellae and bulk γ with small sizes, and a good synergy of strength and ductility. Therefore, this novel approach holds considerable potential as a cost-effective alternative strategy for producing TiAl components.

Investigating phase transformation, densification and diffusion mechanism of TiH 2 powder to achieve a high ductile Ti6Al4V alloy

Phase Transformation, Microstructural Evolution and Tensile Properties of a TiH2-Based Powder Metallurgy Pure Titanium

Improving the Mechanical Processing of Titanium by Hydrogen Doping: A First-Principles Study

Revealing Dehydrogenation Effect and Resultant Densification Mechanism During Pressureless Sintering of TiH2 Powder

Phase Transformations and Formation of Ultra-Fine Microstructure During Hydrogen Sintering and Phase Transformation (HSPT) Processing of Ti-6Al-4V

Effect of Compaction Pressure on the Densification, Microstructure, and Mechanical Properties of Ti‐1Al‐8V‐5Fe Alloy Based on TiH 2 and HDH‐Ti Powders

Hydrogen Sintering, Microstructure, and Mechanical Properties of Ti-10V-2Fe-3Al Alloys Prepared by the Blended Elemental Method

Sintering densification behaviors of Ti-1Al-8V-5Fe alloy based on TiH2 and TiH1.5 powders

In Situ Investigation on Densification Mechanism of Ti-20Al-19Nb (at.%) Alloy by TiH2-assisted Pressureless Sintering

An Experimental Study of the (ti–6al–4v)–xh Phase Diagram Using in Situ Synchrotron XRD and TGA/DSC Techniques

Optimization of Processing Parameters to Produce Nearly Dense Fine-Grained Ti–6Al–4V Microstructures with a Hydrogen-Assisted BEPM Approach

Role of intracrystalline hydrogen on the ductility of dilute Ti-based alloys by first-principles calculations

Effect of Melt Hydrogenation on Microstructure Evolution and Tensile Properties of (tib + TiC)/Ti-6Al-4V Composites

Achieving Excellent Strength-Ductility Synergy of Ti6Al4V Alloy Produced by Powder Metallurgy and Thermo-Mechanical Treatment

The Powder Metallurgy Performance of Ti-1Al-8V-5Fe Alloys with Unsaturated Titanium Hydride

Formation of Titanium Hydride in Ti–6Al–4V Alloy

Enhancing strength-ductility synergy in nano-sized TiB 2 /Al composite via rapid solidification and thermo-mechanical processing

A Novel Method to Fabricate High Strength and Ductility Ti-3Al-5Mo-4.5 V Alloy Based on TiH2 and Pre-Hydrogenated Master Alloy Powders

Progress in the Densification of Powder Metallurgical Titanium Alloys

Heterogeneous Precipitate Microstructure in Titanium Alloys for Simultaneous Improvement of Strength and Ductility

Improving the Formability and Mechanical Properties of TiAl Alloy by Direct Forging of Uncondensed Powder