Abstract:Results are presented for modelling of the evaporation and magnetron sputter deposition of Zn(x)O(y) onto an O-terminated ZnO (0001¯) wurtzite surface. Growth was simulated through a combination of molecular dynamics (MD) and an on-the-fly kinetic Monte Carlo (otf-KMC) method, which finds diffusion pathways and barriers without prior knowledge of transitions. We examine the effects of varying experimental parameters, such as substrate bias, distribution of the deposition species and annealing temperature. It was found when comparing evaporation and sputtering growth that the latter process results in a denser and more crystalline structure, due to the higher deposition energy of the arriving species. The evaporation growth also exhibits more stacking faults than the sputtered growth. Post-annealing at 770 K did not allow complete recrystallization, resulting in films which still had stacking faults where monolayers formed in the zinc blende phase, whereas annealing at 920 K enabled the complete recrystallization of some films to the wurtzite structure. At the latter temperature atoms could also sometimes be locked in the zinc blende phase after annealing. When full recrystallization did not take place, both wurtzite and zinc blende phases were seen in the same layer, resulting in a phase boundary. Investigation of the various distributions of deposition species showed that, during evaporation, the best quality film resulted from a stoichiometric distribution where only ZnO clusters were deposited. During sputtering, however, the best quality film resulted from a slightly O rich distribution. Two stoichiometric distributions, one involving mainly ZnO clusters and the other involving mainly single species, showed that the distribution of deposition species makes a huge impact on the grown film. The deposition of predominantly single species causes many more O atoms at the surface to be sputtered or reflected, resulting in an O deficiency of up to 18% in the deposited film and therefore resulting in more stacking faults and phase boundaries. The methods used allow analysis of key mechanisms that occur during the growth process and give hints as to the optimum conditions under which complete crystalline layers can form.

On the Piezoelectric Properties of Zinc Oxide Thin Films Synthesized by Plasma Assisted DC Sputter Deposition

Deposition and Characterization of AZO Thin Films on Flexible Glass Substrates Using DC Magnetron Sputtering Technique

Study on technology of zinc oxide piezoelectric thin film device with surface micromachining substrate

Morphology-controlled atmospheric pressure plasma synthesis of zinc oxide nanoparticles for piezoelectric sensors

Improved piezoelectric properties of zno films obtained by magnetron sputtering power stacking process

Theoretical study on design of ZnO piezoelectric thin film sensors

Deposition and Characterization of Sputtered ZnO Films

Giant Piezoelectric Effect Induced by Porosity in Inclined ZnO Thin Films

Restoring Piezoelectric Properties in 2D Zinc Oxide Nanosheets by Surface Modifications: Implications for Piezoelectric Nanogenerators

Preparation of piezoelectric ZnO films by target facing type of sputtering method

Room-temperature Remote-Plasma Sputtering of C-Axis Oriented Zinc Oxide Thin Films

Modelling the growth of ZnO thin films by PVD methods and the effects of post-annealing

Evaluation of the Piezoresistivity of a Thin Film of ZnO Doped with Fluorine and Deposited via the Ultrasonic Spray Pyrolysis Technique for Applications in Micro/Nano-Electromechanical Sensors

Tailoring of Zinc Oxide-based microstructures to efficiently promote piezocatalytic water oxidation and oxygen production

Synthesis of zinc oxide/carbon fiber composites with improved piezoelectric response by plasma-liquid interaction

Microstructure and Properties of Cu-Doped Zno Films Prepared by Dc Reactive Magnetron Sputtering

Giant Piezoelectric Properties of ZnO Film Doped with Acceptor-Donor Ionic Pair

Surface Development of Polyethylene Terephthalate Films Using Low-Pressure, High-Frequency Argon + Oxygen Plasma on Zinc Powder for Dye-Sensitized Solar Cells

Plasma-deposited reactive species assisted synthesis of colloidal zinc-oxide nanostructures

Reactive sputtered ZnO thin films: Influence of the O2/Ar flow ratio on the oxygen vacancies and paramagnetic active sites

ZnO thin membrane with large piezoelectric constant and high resistivity