Abstract:In this paper, indium tin oxide (ITO) substrates were treated by ethanol, sulfuric acid (98%) and oxygen plasma respectively, based on which organic light-emitting diodes (OLEDs) with the same double-layer structure: ITO/N,N'-bis-(1-naphyl)-N,N'-diphenyl-1,1'- biphenyl-4,4'-diamine(NPB)/tris-(8-hydroxyquinoline) aluminum(Alq(3))/ Mg:Ag/Al were fabricated. The morphology and compositions of differently treated ITO films were analyzed by atomic force microscopy (AFM) and X-ray photoelectron spectroscopy (XPS). AFM results showed that all these treatments didn't change much the average roughness of ITO films, while ethanol has little influence on the large "peak-valley" (P-V) distance of ITO film; ITO film treated by sulfuric acid has suitable surface morphology with low P-V distance, low average roughness and small particle radius. XPS analysis proved that ethanol has the weakest ability to remove carbon contamination on the surface of ITO film which resulted in unevenly distributed current and high barriers for hole injection; sulfuric-acid-treated ITO film has the least contamination of carbon and higher concentration of oxygen vacancies, both of which are helpful for the improvement of devices. In the condition of room temperature and atmosphere and without encapsulation, measurements of the current-voltage, brightness-voltage and lifetime characteristics of these devices were conducted and showed good agreement with what expected from the results of AFM and XPS analysis: the ethanol-treated ITO provides very unstable performance with low efficiency for the device based on it, while the device based on sulfuric-acid-treated ITO anode had even better performance at higher driven voltage (> 7V) comparing with the device based on oxygen-plasma-treated ITO substrate and had the highest current-luminance efficiency (3.2 cd/A) and the longest lifetime (2 hours).

Systematic Investigation of Surface Modification by Organosiloxane Self-Assembled on Indium-Tin Oxide for Improved Hole Injection in Organic Light-Emitting Diodes

Effective Modification of Indium Tin Oxide for Improved Hole Injection in Organic Light-Emitting Devices

Surface Modification and Characterization of Indium–tin Oxide for Organic Light-Emitting Devices

Indium Tin Oxide Anode Self-Assembled Monolayer Modification for Device Performance Improvement of Organic Light-Emitting Diodes

Modification of the Hole Injection Barrier in Organic Light-Emitting Devices Studied by Ultraviolet Photoelectron Spectroscopy

Enhanced Hole Injection and Brightness of Organic Electroluminescent Devices with Indium Tin Oxide Surface Modification Using Oxygen Plasma Treatment

Influence of Surface Modification of IndiumTin Oxide on Performance of Organic Light Emitting Diodes

Electrochemical Treatment of ITO Surface for Performance Improvement of Organic Light-Emitting Diode

Tuning Hole-Injection in Organic-Light Emitting Diodes with Self-Assembled Monolayers

Importance of Indium Tin Oxide Surface Acido Basicity for Charge Injection into Organic Materials Based Light Emitting Diodes

Influence of ITO Surface Treatment on Performance of Organic Light-Emitting Devices

Indium Tin Oxide Surface Treatments for Improvement of Organic Light-Emitting Diode Performance

A Key Issue of Organic Light-Emitting Diodes: Enhancing Hole Injection by Interface Modifying

Modification of Indium Tin Oxide Surface with HCl for Source/Drain Electrodes in Organic Thin Film Transistors

Characterization of Treated Indium Tin Oxide Surface and Interface Formation Between Treated ITO with Phenyl-Diamine

Chlorinated Indium Tin Oxide Electrode by Incl3 Aqueous Solution for High-Performance Organic Light-Emitting Diodes

Modification of ITO Anodes with Self-Assembled Monolayers for Enhancing Hole Injection in OLEDs

Self-assembled Monolayer-Modified ITO for Efficient Organic Light-Emitting Diodes: the Impact of Different Self-Assemble Monolayers on Interfacial and Electroluminescent Properties

Sulfuric Acid Treatment Of Indium Tin Oxide For Application Of Organic Light-Emitting Diodes

Surface Modification of Indium Tin Oxide by Oxygen Plasma Immersion Ion Implantation

Enhancement of hole injection with an ultra-thin Ag2O modified anode in organic light-emitting diodes