Abstract:During the fabrication of an indium-gallium-zinc oxide (IGZO) thin film transistor (TFT), the thermal process was used to reduce the resistivity of IGZO. The annealing temperature was found to have great influence on the transistor characteristics. At an optimized heat-treatment temperature, the depletion-mode IGZO TFT was fabricated with steeper subthreshold slope, higher filed-effect mobility and acceptable turn-on voltage. And the relatively conductive IGZO could directly replace the indium tin oxide as the transparent electrode of the organic light-emitting diode (OLED), reducing the mask count of the backplane for the active-matrix OLED display. INTRODUCTION Thin film transistor (TFT) based on metal oxide (MO), especially, indium-gallium-zinc oxide (IGZO), is considered as a good candidate to fabricate large area backplane for active-matrix organic light-emitting diode (AMOLED) display, due to its high mobility, good uniformity and low off-state current [1]. Our previous study [2] suggested that the resistivity (ρ) of IGZO highly depended on the heat-treatment conditions, such as annealing ambience, temperature, duration and gas permeability of IGZO cover, while the thermal process was often inevitable during the fabrication of IGZO TFT. With the active layer of IGZO covered with the gas-permeable silicon oxide (SiOx), the TFT was subjected to a serious anneals in an oxygen-deficient nitrogen (N2) ambience. With the increasing temperature, although the mobility was enhanced, the turn-on voltage (Von) became more and more negative. At an optimized temperature, the depletion-mode (DM) IGZO TFT with steeper subthreshold slope, higher filed-effect mobility and acceptable turn-on voltage was fabricated. Furthermore, such annealing-induced conductive IGZO source/drain regions can be directly used to replace the indium tin oxide (ITO) as the transparent electrode of OLED, reducing the mask count of AMOLED backplane. Annealing-Induced DM IGZO TFT Shown in Figure 1 is the evolution of the schematic cross-section of an IGZO TFT. A gate dielectric of 100 nm silicon oxide (SiOx) was first thermally grown on an n+ silicon substrate, which served as the gate electrode. 10 or 20 nm IGZO film was then room-temperature sputtered using a target of In2O3:Ga2O3:ZnO = 1:1:1 mol% in an atmosphere of 10% oxygen (O2) and 90% argon (Ar). After the patterning of the active-island using the hydrofluoric acid, a passivation layer of 300 nm SiOx was deposited at 300 oC in a plasma-enhanced chemical vapor deposition (PECVD) reactor. The tetraethylorthosilicate (TEOS) and O2 were used as the source gases. The contact holes were then opened and the resulting structure was subjected to a series of anneals, as shown in Figure 1a. Finally, 300 nm aluminum (Al) was deposited and patterned into electrodes (Fig. 1b). These TFTs were measured using an Agilent 4156C semiconductor parameter analyzer. n+ Si 100nm SiOx 300nm SiOx

Self-Aligned Bottom-Gate In—Ga—Zn—O Thin-Film Transistor With Source/Drain Regions Formed by Direct Deposition of Fluorinated Silicon Nitride

Deep Sub-Micron Self-Aligned Bottom-Gate Amorphous InGaZnO Thin-Film Transistors With Low-Resistance Source/Drain

Self-aligned Top-Gate InGaZnO Thin Film Transistors Using SiO2/Al2O3 Stack Gate Dielectric

Sub-100 Nm Self-Aligned Top-Gate Amorphous InGaZnO Thin-Film Transistors with Gate Insulator of 4 Nm Atomic-Layer-Deposited AlOx

Self-aligned Indium–gallium–zinc Oxide Thin-Film Transistors with SiNx/SiO2/SiNx/SiO2 Passivation Layers

A Bottom-Gate Indium-Gallium-Zinc Oxide Thin-Film Transistor With an Inherent Etch-Stop and Annealing-Induced Source and Drain Regions

Self-Aligned Indium–Gallium–Zinc Oxide Thin-Film Transistor with Source/Drain Regions Doped by Implanted Arsenic

Self-Aligned Indium–Gallium–Zinc Oxide Thin-Film Transistor with Phosphorus-Doped Source/Drain Regions

Scalability and Stability Enhancement in Self-Aligned Top-Gate Indium- Zinc-Oxide TFTs with Al Reacted Source/Drain

40‐4: Invited Paper: Self‐Aligned Top‐Gate Amorphous In‐Ga‐Zn‐O Thin‐Film Transistors with Hafnium‐Induced Source/Drain Regions

A Simple Doping Process Achieved by Modifying the Passivation Layer for Self-Aligned Top-Gate In-Ga-Zn-O Thin-Film Transistors at 200 degrees C

Top-Gate Amorphous Indium-Gallium-Zinc-OxideThin-Film Transistors With Magnesium Metallized Source/Drain Regions

Gate Insulator Engineering in Top-Gated Indium-Tin-Oxide-Stabilized ZnO Thin-Film Transistors

Self-aligned Top-Gate Amorphous Oxide Thin-Film Transistors with IZO/IGZO Stacked Active Layer and Al Reacted Source/drain Region

A Simple Doping Process Achieved by Modifying the Passivation Layer for Self-Aligned Top-Gate In-Ga-Zn-O Thin-Film Transistors at 200 °C

Self-Aligned Top-Gate Amorphous InGaZnO TFTs with Plasma Enhanced Chemical Vapor Deposited Sub-10 Nm SiO2 Gate Dielectric for Low-Voltage Applications

Self-Aligned Top-Gate Metal-Oxide Thin-Film Transistors Using a Solution-Processed Polymer Gate Dielectric

Annealing-Induced Depletion-Mode Indium-Gallium-Zinc Oxide Thin-Film Transistor and Its Application to Active-Matrix Organic Light-Emitting Diode Display

Fully Self-Aligned Homojunction Bottom-Gate Amorphous InGaZnO TFTs with Al Reacted Source/Drain Regions

A-Igzo TFTs with Inductively Coupled Plasma Chemical Vapor Deposited ${\rm SiO}_{x}$ Gate Dielectric

High-Performance Self-Aligned Top-Gate Amorphous InGaZnO TFTs with 4 Nm-Thick Atomic-Layer-Deposited AlOx Insulator