Abstract:Global warming, driven by greenhouse gases like CH4 and CO2, necessitates efficient catalytic conversion to syngas. Herein, Ni containing different molecular sieve nanomaterials are investigated for dry reforming of methane (DRM). The reduced catalysts are characterized by surface area porosity, X-ray diffraction, Raman infrared spectroscopy, CO2 temperature-programmed desorption techniques, and transmission electron microscopy. The active sites over each molecular sieve remain stable under oxidizing gas CO2 during DRM. The reduced 5Ni/CBV10A catalyst, characterized by the lowest silica-alumina ratio, smallest surface area and pore volume, and narrow 8-ring connecting channels, generated the maximum number of active sites on its outer surface. In contrast, the reduced-5Ni/CBV3024E catalyst, with the highest silica-alumina ratio, more than double the surface area and pore volume, 12-ring sinusoidal porous channels, and smallest Ni crystallite, produced the highest H2 output (44%) after 300 min of operation at 700 °C, with a CH4:CO2 = 1:1, P = 1 atom, gas hour space velocity (GHSV) = 42 L gcat-1 h-1. This performance was achieved despite having 25% fewer initial active sites, suggesting that a larger fraction of these sites is stabilized within the pore channels, leading to sustained catalytic activity. Using central composite design and response surface methodology, we successfully optimized the process conditions for the 5Ni/CBV3024E catalyst. The optimized conditions yielded a desirable H2 to CO ratio of 1.00, with a H2 yield of 91.92% and a CO yield of 89.16%, indicating high efficiency in gas production. The experimental results closely aligned with the predicted values, demonstrating the effectiveness of the optimization approach.

Response Surface Methodology for Ni-Zeolite Catalyst Optimization in Syngas Production

Process Optimization for Syngas Production from the Dry Reforming of Methane over 5Ni+3Sr/10Zr+Al Catalyst Using Multiple Response Surface Methodology

Highly-stable Ni–Zn catalyst on USY zeolite support for low temperature methane pyrolysis

Carbon Dioxide Reforming of Methane over Nickel-Supported Zeolites: A Screening Study

Impact of varied zeolite materials on nickel catalysts in CO 2 methanation

Metal-foam-structured Ni–Al2O3 Catalysts: Wet Chemical Etching Preparation and Syngas Methanation Performance

Ni-Based Molecular Sieves Nanomaterials for Dry Methane Reforming: Role of Porous Structure and Active Sites Distribution on Hydrogen Production

Ni–Al2O3 Catalysts Prepared by Solution Combustion Method for Syngas Methanation

Partial Oxidation Of Methane To Syngas Over Ni-Based Catalysts

Insights into the Zn Promoter for Improvement of Ni/SiO 2 Catalysts Prepared by the Ammonia Evaporation Method toward CO 2 Methanation

Tailored Ni-MgO Catalysts: Unveiling Temperature-Driven Synergy in CH4-CO2 Reforming

Zeolite-Supported Ni Catalysts for CO2 Methanation: Effect of Zeolite Structure and Si/Al Ratio

Synergistic interplay of dual active sites on spinel ZnAl2O4 for syngas conversion

Boosting CO2 hydrogenation to methane over Ni-based ETS-10 zeolite catalyst

Optimizing CO2 methanation: effect of surface basicity and active phase reducibility on Ni-based catalysts

Impact of Heating Rate and Solvent on Ni-based Catalysts Prepared by Solution Combustion Method for Syngas Methanation

Catalytic Methanation of Syngas over Ni-based Catalysts with Different Supports

Hydrothermal Gasification of Microalgae over Nickel Catalysts for Production of Hydrogen-Rich Fuel Gas: Effect of Zeolite Supports

High-Stability ZnAl2O4 Spinel-Supported Nickel Catalyst for High-Temperature Syngas Methanation

Methane Dry Reforming by Ni-Cu Nanoalloys Anchored on Periclase-Phase MgAlO<i><sub>x</sub></i> Nanosheets for Enhanced Syngas Production

Simulative Optimization of Catalyst Configuration for Biogas Dry Reforming