Abstract:Masonry structures often exhibit poor seismic performance during earthquakes owing to their low material strength, structural integrity, and ductility. To address the mechanism of in-plane damage and collapse of masonry walls subjected to earthquake ground motion, three full-size brick walls, one with structural columns and two without structural columns, were designed and constructed in this experimental study to quantitatively investigate the effect of structural columns on the seismic performance of masonry walls. Quasi-static tests of masonry walls subjected to cyclic lateral loading were conducted using electrohydraulic servo actuators. The in-plane damage evolution and failure mode of the masonry walls under lateral loading were investigated. A numerical model with a novel plastic damage constitutive model of masonry was established. The accuracy of this model and the calculation results were verified by comparing them with the crack development and mechanical property curves obtained from the experiments. Based on the numerical model, a parametric analysis was conducted to investigate the influence of critical factors, such as mortar strength, vertical load, and height-to-width ratio, on the seismic performance of masonry structures. The test results showed that structural columns can effectively improve the performance of masonry structures. Properly installed structural columns can improve the peak load-bearing capacity, ductility, and energy dissipation of masonry structures. The masonry damage constitutive model used in this study could simulate the damage to masonry wall specimens well and reflect the hysteretic curves of the specimens within an acceptable range of accuracy. Thus, it provides a valuable reference for physical experiments. An appropriate mortar strength and vertical compressive stress can effectively enhance the load-bearing capacity of masonry structures within a certain range. For structural column walls. Walls with mortar strengths (average compressive strength) of 12.5 MPa, 10 MPa, 7.5 MPa, and 5 MPa showed an increase in peak bearing capacity of 26.2 %, 23.9 %, 18.5 %, and 9.4 %, respectively, compared to walls with mortar strengths (average compressive strength) of 2.5 Mpa. The aspect ratio had a significant impact on the shear load-bearing capacity of the masonry walls. An increase in the aspect ratio led to a transition from shear failure to flexural failure and a subsequent decrease in shear load-bearing capacity. For masonry walls with structural columns, increasing the diameter of the longitudinal steel in the structural columns can enhance the load-bearing capacity of the masonry wall, resulting in a significant improvement in its overall performance.

Displacement‐based seismic analysis for out‐of‐plane bending of unreinforced masonry walls

Simulation Of Collapse Process Of Masonry Walls Based On Expanded Discrete Element Method

A block-based numerical strategy for modeling the dynamic out-of-plane behavior of unreinforced brick masonry walls

Analytical modeling of masonry load-bearing walls

Finite element-based reliability analysis of reinforced concrete masonry walls under eccentric axial loading considering slenderness effects

In-plane shear strength and damage fragility functions for partially-grouted reinforced masonry walls with bond-beam reinforcement

Nonlinear finite and discrete element simulations of multi-storey masonry walls

A Static Nonlinear Analysis of Confined Brickmasonry Walls in a Multistory Building with a Large-Bay

Dynamic characteristics of stone masonry walls before and after damage: Experimental and numerical investigations

Damage evolution and failure mechanism of masonry walls under in-plane cyclic loading

Analytical formulation describing the behaviour of URM walls seismically strengthened using timber strong-backs

An improved method for statistics estimation of out-of-plane load resistance of masonry walls using design-code models and mechanics-based finite element models

In-Plane Lateral Response of a Full-Scale Masonry Subassemblage with and without an Inorganic Matrix-Grid Strengthening System

Discrete Element Modeling of the Seismic Behavior of Masonry Construction

Numerical homogenization‐based seismic assessment of an English‐bond masonry prototype: Structural level application

Backbone Model for Confined Masonry Walls for Performance-Based Seismic Design

Explicit Approach for the In-Plane Cyclic Behaviors of Unreinforced Masonry Structures Using Finite Particle Method

Strain Monitoring and Crack Detection in Masonry Walls under In-Plane Shear Loading Using Smart Bricks: First Results from Experimental Tests and Numerical Simulations

Simulation of Masonry Wall using Concrete Damage Plasticity Model

Seismic assessment of the in‐plane/out‐of‐plane interaction of masonry infills in a two‐storey RC building subjected to bi‐directional shaking table tests

Experimental Investigation of Effect of Section Configuration on Seismic Performance of an Innovative Integrated Concrete Masonry Wall System