Abstract:Micro-electro-mechanical system (MEMS) is a newly rising interdisciplinary, technology. The mechanical design of MEMS is one of the frontiers of mechanical engineering. The increasing use of small micro-electro-mechanical system (MEMS) and advanced sensors has lead to concern about the failure modes and reliability of these structures. This depends on the solution of materials issues associated with the design and fabrication of complex MEMS devices. The reliable mechanical properties of these thin films are critical to the safety and functioning of these microdevices and should be accurately determined. This paper takes up the key point among the existing problems in the development of MEMS, the mechanical behavior of MEMS materials, for investigating experimentally in detail. To investigate the specimen size influence on fracture strength of microstructures, the validity of a novel, direct and convenient method for bending strength measurements by beam bending using a nanoindenter has been demonstrated. The tensile strength of polysilicon thin films was measured with a microtensile test device with a magnet solenoid actuator and a fibre optical displacement sensor. The bending strength of microfabricated polysilicon beams with dimensions of 16 ∼ 34 μm long, 10 ∼ 50 μm wide, and 2.4 μm thick was evaluated. The tensile mechanical properties of microfabricated polysilicon thin films with dimensions of 100 ∼ 660 μm long, 20 ∼ 200 μm wide, and 2.4 μm thick were also evaluated. The result shows that bending strength and tensile strength of polysilicon microstructures show size effect on the size of the specimens. Statistical analysis of bending strength and tensile strength for various specimen sizes shows that the average bending strength of polysilicon microcantilever beams is (2.885 ± 0.408) GPa, and the average tensile strength of polysilicon thin films is (1.36 ± 0.14) GPa. Statistical analysis of the specimen size effects on the tensile strength predicated the size effects on the length, the surface area and the volume of the specimens due to microstructural and dimensional constrains. The fracture strength increases with the increase of the ratio of surface area to volume. In such cases the size effect can be traced back to the ratio of surface area to volume as the governing parameter. The test data accounts for the uncertainties in mechanical properties and may be used in the future reliability design of polysilicon MEMS structures.

Performance analysis of Micro-cantilever beams and sensor data fitting

Dimension effect on mechanical behavior of silicon micro-cantilever beams

Specimen Size Effect on Mechanical Properties of Polysilicon Microcantilever Beams Measured by Deflection Using A Nanoindenter

Role of material microstructure in plate stiffness with relevance to microcantilever sensors

Static deflections analysis of micro-cantilevers beam under transverse loading

Direct influence of residual stress on the bending stiffness of cantilever beams

On Nonlocal Vertical and Horizontal Bending of a Micro-Beam

RESEARCH OF THE SIZE EFFECT ON STRENGTH OF POLYSILICON MICRO-ELECTRO-MECHANICAL DEVICES

Fabrication and Fatigue Testing of an Electrostatically Driven Microcantilever Beam

Specimen Size Effect on Fracture Strength of Polysilicon Microcantilever Beam s

An updated model including the deflection history of microcantilever for characterizing cellular viscoelastic properties by AFM indentation-relaxation test

Evaluation of Mechanical Properties and Strain Criterion for Realibility Design of Micromachined Polysilicon Thin Films

Extension of the Beam Theory for Polymer Bio-Transducers with Low Aspect Ratios and Viscoelastic Characteristics

A Modified Analytical Model to Study the Sensing Performance of a Flexible Capacitive Tactile Sensor Array

Research on a Precision Calibration Model of a Flexible Strain Sensor Based on a Variable Section Cantilever Beam

Experiments on the Deformation of MEMS Mciro-Cantilever Using AFM

Design analysis, modeling and simulation of novel rectangular cantilever beam for MEMS sensors and energy harvesting applications

Calibration Model Optimization for Strain Metrology of Equal Strength Beams Using Deflection Measurements

Micro-cantilever bending tests for understanding size effect in gradient elasticity

Finite Element Modelling of Micro-cantilevers Used as Chemical Sensors

Fabrication and Analysis of Micromachined Cantilever Array