Abstract:Silicon carbon nitride thin films were deposited on Co-Cr alloy under varying deposition conditions such as sputtering power and the partial pressure ratio of N(2) to Ar by radio frequency and direct current magnetron sputtering techniques. The chemical bonding configurations, surface topography and hardness were characterized by means of X-ray photoelectron spectroscopy, atomic force microscopy and nano-indentation technique. The sputtering power exhibited important influence on the film composition, chemical bonding configurations and surface topography, the electro-negativity had primary effects on chemical bonding configurations at low sputtering power. A progressive densification of the film microstructure occurring with the carbon fraction was increased. The films prepared by RF magnetron sputtering, the relative content of the Si-N bond in the films increased with the sputtering power increased, and Si-C and Si-Si were easily detachable, and C-O, N-N and N-O on the film volatile by ion bombardment which takes place very frequently during the film formation process. With the increase of sputtering power, the films became smoother and with finer particle growth. The hardness varied between 6 GPa and 11.23 GPa depending on the partial pressure ratio of N(2) to Ar. The tribological characterization of Co-Cr alloy with Si-C-N coating sliding against UHMWPE counter-surface in fetal bovine serum, shows that the wear resistance of the Si-C-N coated Co-Cr alloy/UHMWPE sliding pair show much favourable improvement over that of uncoated Co-Cr alloy/UHMWPE sliding pair. This study is important for the development of advanced coatings with tailored mechanical and tribological properties. Crown Copyright (C) 2011 Published by Elsevier B.V. All rights reserved.

Silicon Nitride Gradient Film As the Underlayer of Ultra-Thin Tetrahedral Amorphous Carbon Overcoat for Magnetic Recording Slider

FePt-Si-N nano-granular thin films with improved structure and magnetic properties for high-density recording medium

Development of FePt-Si-N nanocomposite thin films for magnetic recording

Effect of ECR-assisted Microwave Plasma Nitriding Treatment on the Microstructure Characteristics of FCVA Deposited Ultra-Thin Ta-C Films for High-Density Magnetic Storage Applications

Continuous Ultra-Thin Carbon Nitride Thin Film for Magnetic Hard Disk Via Post Nitrogen Plasma Treatment

The Structure, Surface Topography and Mechanical Properties of Si–C–N Films Fabricated by RF and DC Magnetron Sputtering

Microstructure, Mechanical Properties and Wetting Behavior of F: Si–C–N Films As Bio-Mechanical Coating Grown by DC Unbalanced Magnetron Sputtering

Co Filled Porous Anodic Alumina Film Fabricated on Ecr-Al Film with Silicon Substrate

Magnetic Exchange-Coupled Sm(Co,R)/Cr(R = Al, Si, Ti, Nb, Cu) Series Films for Ultrahigh-Density Longitudinal Recording Media

The Protective Properties of Ultra-Thin Diamond Like Carbon Films for High Density Magnetic Storage Devices

CoPt/Ag(Cu) Nanocomposite Films for Ultra-High Density Perpendicular Magnetic Recording Media

Synthesis, composition, surface roughness and mechanical properties of thin nitrogenated carbon films

Silicon Nitride Films for the Protective Functional Coating: Blood Compatibility and Biomechanical Property Study.

Growth of high quality Si-based (Gd<sub>2</sub>Ce)(Fe<sub>4</sub>Ga)O<sub>12</sub> thin film and prospects as a magnetic recording media

Molecular Dynamics Study Of Nano-Tribological Properties Of Silicon Nitride Films

Multilayer structure design for preparing ultralow wear amorphous carbon films

High Coercivity Feptsin Films With L1(0)-Fept Nanoparticles Embedded In A Si-Rich Matrix

Design Consideration and Practical Solution of High-Performance Perpendicular Magnetic Recording Media

Microstructure of Electroless Co Alloy Films for Perpendicular Magnetic Recording

NiW/Ru Underlayer for CoPt-SiO2 Granular Perpendicular Recording Media.

Corrosion Protection of Ultra-Thin Ta-C Films for Recording Slider Applications at Varied Substrate Bias