Abstract:Amorphous carbon (a-C), one of the most studied carbon-based films, has been widely applied in the filed of artificial joints due to its excellent mechanical and tribological properties and high corrosion resistance. However, low adhesive strength and poor fatigue resistance are fatal shortcomings of this kind of films. In this study, carbon (sp2-C:Ti/sp3-C:Ti) nano-multilayer films (MFs) with sequential sp3-rich and sp2-rich layers were deposited on Ti6Al4V and c-Si substrate by DC magnetron sputtering. X-ray diffraction, scanning electron microscopy, the X-ray photoelectron spectroscopy and the transmission electron microscopy were used to characterize the composition, structure and morphologies of the MFs. In the sp2-C:Ti/sp3-C:Ti MFs, the sp3-C rich layer and the sp2-C rich layer exhibit amorphous features and onion-like structure, respectively. Moreover, the layered structure is continuous in a relatively clear region but with a rough layer interface. The mechanical and the scratch behaviors were elaborately characterized by nanoindentation and scratch tests. The results revealed that the sp2-C:Ti/sp3-C:Ti MFs possess hardness of 21.9 GPa and excellent scratch behavior at sputtering bias voltage −220 V, which are significantly better than single-layer films. Furthermore, the adhesion and tribological behaviors of the sp2-C:Ti/sp3-C:Ti MFs were obtained by Rockwell and ball-on-disk tribometer tests. It was found that the sp2-C:Ti/sp3-C:Ti MFs synthesized under a sputtering bias of −220 V not only exhibit relatively low coefficient of friction (only 0.11) in humid air, but also present lower coefficient of friction (0.085) and wear rate (7.5 × 10−17m3N−1 m−1) of Si3N4 balls in Fetal bovine serum (FBS) solution. In conclusion, the critical loads and wear resistance of the sp2-C:Ti/sp3-C:Ti-MFs were effected by the sputtering bias and the mechanical properties of the MFs. And when sputtering bias is −220 V, the sp2-C:Ti/sp3-C:Ti MFs exhibited the improved mechanical properties, the lowest coefficient of friction (CoF) and the highest wear resistance.

Multilayer structure design for preparing ultralow wear amorphous carbon films

Influencing mechanisms of deposition bias voltage on superlubricious a-C:H films: Key role of nanoclustering structures in controlling structural evolution of transfer film

Tribology dependence on both structures of bulk a-C:H:Si films and transfer layer via adjustable Si content

Fullerene-like Nanostructure Induced Excellent Friction Behavior in High Vacuum Environment for Hydrogenated Carbon Film

Structural and tribological behaviours of silicon doped amorphous carbon films

Design architecture of colorful Si-DLC/PLC nanostructured multilayer films for robust superlubricity at high contact stress in dry N2 atmosphere

Influence of Modulation Periods on the Tribological Behavior of Si/a-C: H Multilayer Film

Ultra-low Friction of A-C:H Films Enabled by Lubrication of Nanodiamond and Graphene in Ambient Air

Influence of individual Cr–C layer thickness on structural and tribological properties of multilayered Cr–C/a-C:Cr thin films

Lithium Citrate Triggered Macroscopic Superlubricity with Near-Zero Wear on an Amorphous Carbon Film

Genesis of Superlow Friction in Strengthening Si-DLC/PLC Nanostructured Multilayer Films for Robust Superlubricity at Ultrahigh Contact Stress.

Effect of a-C:H:Si interlayers on the mechanical and superlubricious properties of hydrogenated amorphous carbon films

Structure Effects of Sp2-Rich Carbon Films under Super-Low Friction Contact

Theoretical superlubricity and its friction stability of amorphous carbon film induced by simple surface graphitization

Achieving superlubricity and high adhesion strength of hydrogenated amorphous carbon film with Al/Cr/Si-doping

Tribological performances of a-C films tested on dry nitrogen environment with various Hertz pressures: Failure mechanisms and in-situ formation graphene

Structure and Characterization of TiC/GLC Multilayered Films with Various Bilayers Periods

Structural and environmental dependence of superlubricious properties in hydrogenated Graphite-Like carbon Films: Implications in solid state lubrication

Mechanical and Tribological Properties of Cr/Cr2O3 Multilayer Films

Structure, mechanical properties and tribological behavior of sp2-C:Ti/sp3-C:Ti multilayer films deposited by magnetron sputtering

Regulating Vacuum Tribological Behavior of A-C:H Film by Interfacial Activity.