Abstract:A wideband low-noise amplifier (LNA) with low and flat noise figure (NF) is presented in this article. For conventional wideband noise matching, the noise performance in the high-frequency region of the entire wideband is usually deteriorated due to the frequency-dependent nature of the minimum noise figure (NFmin) for a MOSFET. To address this issue, a novel wideband noise matching approach aiming at noise matching in high band is proposed. This approach can reduce the NF in high band at the cost of a slight NF increase in low band, eventually achieving a low and flat NF and thus a better overall noise performance for a wideband LNA. In addition, the multistage noise matching technique is employed at high frequencies to further reduce the NF caused by the second amplification stage. To validate the proposed techniques, a two-stage LNA prototype was designed and fabricated using a 65 nm CMOS process. The experimental results indicate a peak gain of 16.6 dB with a −3 dB bandwidth (BW) from 7.2 to 27.3 GHz (a fractional BW of 116%). Within the entire band of interest, the simulated NF is low and almost constant (3.3–3.4 dB), while the measured NF falls within the range of 3.30–3.72 dB. Considering the uncertainty of NF measurement, a 0.21 dB NF flatness is one of the best results among the reported millimeter-wave wideband LNAs. The measured third-order input intercept point (IIP3) is −6 dBm at 20 GHz, while the power consumption is 13.2 mW. In addition, only two passive transformers are used in this design, leading to a compact chip core area (0.14 mm2).

A 0.13-μm CMOS 0.8–10.6GHz low noise amplifier with active balun for multi-standard applications

A 0.13-Mu M Cmos 0.1-12 Ghz Active Balun-Lna For Multi-Standard Applications

Analysis and Design of Ultra-Wideband Low-Noise Amplifier with Input/Output Bandwidth Optimization and Single-Ended/Differential-Input Reconfigurability.

0.9–10GHz low noise amplifier with capacitive cross coupling

A high-gain wideband balun-LNA with multiple noise-optimized technique

Compact CMOS Baluns for the 4–10 GHz Band Applications

A Compact 2.1–39 GHz Self-Biased Low-Noise Amplifier in 65 Nm CMOS Technology

A 6.512-GHz Balanced Variable-Gain Low-Noise Amplifier With Frequency-Selective Gain Equalization Technique

3-10 GHz self-biased resistive-feedback lna with inductive source degeneration

A 0.061-Mm² 1–11-Ghz Noise-Canceling Low-Noise Amplifier Employing Active Feedforward with Simultaneous Current and Noise Reduction

0.2–4.35 GHz Highly Linear CMOS Balun-Lna with Substrate Noise Optimization

A CMOS Wide-Band Low-Noise Amplifier with Balun-Based Noise-Canceling Technique

A CMOS 0.5&#x2013;10.6 GHz Inductor Feedback Low Noise Amplifier for Multi-Standard Application

A 4.7-to-18-ghz Ultra-Wideband Variable-Gain Balun-LNA Using 3 Rd -Order-band-pass Input Matching in 40-Nm CMOS.

A 6–9 GHz UWB balun-LNA employing current-reuse with preamplifier and CCC buffer

A 7.2–27.3 GHz CMOS LNA With 3.51 ±0.21 dB Noise Figure Using Multistage Noise Matching Technique

Inductor-less PVT robust gain switching balun LNA for multistandard applications

A 28 GHz balun‐first LNA with db‐linear 32 db gain range for 5 G applications

A High-Gain Low-Power Balun-Lna for 6&#x2013;9ghz UWB System

A dual band CMOS two-stage variable gain low noise amplifier

A Low Power High Gain UWB LNA in 0.18-Μm CMOS