Abstract:This article reports a high-gain wideband low-noise amplifier (LNA) with single ended input and differential output for multi-standard wireless receiver operating in 0.2 to 7 GHz. The proposed balun-LNA is cascode structure with common-gate–common-source (CG–CS) balun load to achieve single to differential conversion. Focusing on improving the voltage gain, bandwidth and noise performance at the same time, several techniques are implemented in this balun-LNA. A current source is added shunting CG stage to relieve voltage headroom and improve gain and linearity. Wideband input matching is achieved by active shunt-shunt resistive feedback, together with the input series inductor. Moreover, feedforward and current-reuse technique are introduced to further optimize the noise performance. The proposed LNA has a measured voltage gain of 26 dB which is nearly 6 dB higher than other balun-LNA with same supply and process. Moreover, the minimum noise figure (NF) is 2.0 dB owing to multiple noise-optimized technique. The achieved input power at 1 dB gain compression point (IP1 dB) is −14 dB m at 1 GHz and input return loss ( S11 ) is better than −10 dB across entire operating frequency range. IIP3 and IIP2 achieve −7 dBm and 25 dBm respectively, measured at 1 GHz. The power consumption is 15.5 mW at 1.2 V supply. The LNA is fabricated in 130 nm CMOS process and the active area is 0.097 mm2 . The LNA achieves high voltage gain and wide operating frequency range with low NF, which can be reflected from the figure of merit (FOM) of 23.1.

A CMOS Wide-Band Low-Noise Amplifier with Balun-Based Noise-Canceling Technique

A BiCMOS Implementation of Noise Canceling Low Noise Amplifier for Wideband Applications

A Wideband BiCMOS Thermal Noise Canceling Low Noise Amplifier with Temperature Compensation

Analysis and Design of Ultra-Wideband Low-Noise Amplifier with Input/Output Bandwidth Optimization and Single-Ended/Differential-Input Reconfigurability.

Analysis And Design Of Inductorless Wideband Low-Noise Amplifier With Noise Cancellation Technique

A 0.061-Mm² 1–11-Ghz Noise-Canceling Low-Noise Amplifier Employing Active Feedforward with Simultaneous Current and Noise Reduction

A Compact 2.1–39 GHz Self-Biased Low-Noise Amplifier in 65 Nm CMOS Technology

A 6.512-GHz Balanced Variable-Gain Low-Noise Amplifier With Frequency-Selective Gain Equalization Technique

Ultralow Power E-Band Low-Noise Amplifier with Three-Stacked Current-Sharing Amplification Stages in 28-Nm CMOS

A 0.13-μm CMOS 0.8–10.6GHz low noise amplifier with active balun for multi-standard applications

A 0.13-Mu M Cmos 0.1-12 Ghz Active Balun-Lna For Multi-Standard Applications

A high-gain wideband balun-LNA with multiple noise-optimized technique

Two-Fold Noise-Cancelling Low-Noise Amplifier in 28-nm CMOS

A 23-30 GHz LNA with Noise-Cancelling in 28nm CMOS

0.2–4.35 GHz Highly Linear CMOS Balun-Lna with Substrate Noise Optimization

A Novel CMOS Low-Noise Amplifier Design for 3.1- to 10.6-Ghz Ultra-Wide-band Wireless Receivers

A Q-band CMOS LNA Exploiting Transformer Feedback and Noise-Cancelling

Gain-controlled CMOS Low Noise Amplifier

A 0.0081mm2 0.15–5.9-Ghz Low Noise Amplifier with Noise Cancelling and Current Reuse Techniques

A 2.8–10-GHz CMOS Current Reuse Cascaded Linearity Improving Ultra-Wideband Low-Noise Amplifier

A 0.18 Mu M Cmos Ultra-Wideband Low-Noise Amplifier With High Iip3