Abstract:The front-end electronics (FEE) of the Compact Muon Solenoid (CMS) is needed very low power consumption and higher readout bandwidth to match the low power requirement of its Short Strip application-specific integrated circuits (ASIC) (SSA) and to handle a large number of pileup events in the High-Luminosity Large Hadron Collider (LHC). A low-noise, wide bandwidth, and ultra-low power FEE for the pixel-strip sensor of the CMS has been designed and simulated in a 0.35 µm Complementary Metal Oxide Semiconductor (CMOS) process. The design comprises a Charge Sensitive Amplifier (CSA) and a fast Capacitor-Resistor-Resistor-Capacitor (CR-RC) pulse shaper (PS). A compact structure of the CSA circuit has been analyzed and designed for high throughput purposes. Analytical calculations were performed to achieve at least 998 MHz gain bandwidth, and then overcome pileup issue in the High-Luminosity LHC. The spice simulations prove that the circuit can achieve 88 dB dc-gain while exhibiting up to 1 GHz gain-bandwidth product (GBP). The stability of the design was guaranteed with an 82-degree phase margin while 214 ns optimal shaping time was extracted for low-power purposes. The robustness of the design against radiations was performed and the amplitude resolution of the proposed front-end was controlled at 1.87% FWHM (full width half maximum). The circuit has been designed to handle up to 280 fC input charge pulses with 2 pF maximum sensor capacitance. In good agreement with the analytical calculations, simulations outcomes were validated by post-layout simulations results, which provided a baseline gain of 546.56 mV/MeV and 920.66 mV/MeV, respectively, for the CSA and the shaping module while the ENC (Equivalent Noise Charge) of the device was controlled at 37.6 e- at 0 pF with a noise slope of 16.32 e-/pF. Moreover, the proposed circuit dissipates very low power which is only 8.72 µW from a 3.3 V supply and the compact layout occupied just 0.0205 mm2 die area.

A Low Noise Reference Generator in Monolithic Active Pixel Sensors for Star

A Full On-Chip, Low Noise, Low Power Consumption Reference Generator in Monolithic Active Pixel Sensors

A Novel Fully On-Chip CMOS Low-Dropout Linear Regulator with Ultra Low Noise

A Novel Ultra Low Noise CMOS Voltage Reference Circuit with Digital Calibration Scheme

A 200 Ma Low-Area, Low-Noise, Low-Dropout Linear Regulator for Monolithic Active Pixel Sensors

A Low-Power-Consumption, Supply-Noise-Insensitive Charge Pump Pll with A Voltage Regulator for On-Chip Clock Generating in Maps at Star Experiment

A High Load Current, Low-Noise, Area-Efficient, Full On-Chip Regulator for Cmos Pixel Sensors

A low-noise and low-area-consumption power management dedicated to CMOS pixel sensors for high energy physics experiments

Design of reference voltage source integrated in LCoS chip

A Supply-Noise-Insensitive PLL in Monolithic Active Pixel Sensors

A Full Functional Monolithic Active Pixel Sensor Prototype for the CEPC Vertex Detector

Design of a Pixel Readout ASIC Using Super Pixel Circuits with a Built-in LDO Regulator for Hybrid X-ray Imaging Detectors

Design of an 11-Bit Column-parallel ADC for Monolithic Active Pixel Sensor

High Consistency Ramp Design Method for Low Noise Column Level Readout Chain

Novel design of reference voltage source integrated in LCoS chip

A Digitally Controlled On-chip Monotonic Reference Current Generator with Low LSB Current for Fast and Accurate Optical Level Monitoring

An Inverter-based On-chip Voltage Reference Generator for Low Power Application

A Low Noise, High PSR, Low Dropout Linear Regulator

An 8.72 µW Low-Noise and Wide Bandwidth FEE Design for High-Throughput Pixel-Strip (PS) Sensors

Two Ramp Reference Voltages CDS Scheme Applied to Low Noise and High Dynamic Range PWM Pixel

A Bandgap Voltage Reference Generator for an Analogue-to-digital Converter