Abstract:With the increasing depletion of high-quality raw materials, siliceous limestone, sandstone and other hard-to-burn raw materials containing crystalline SiO2 are gradually being used to produce clinker. This study investigates the influence of the quartz content and particle size in siliceous limestone on the calcination process and the resultant quality of cement clinker. Two different siliceous limestones were grinded to different fineness, and calcinated with some other materials. The content of the clinkers was analyzed with the XRD–Rietveld method and the microstructure of the clinkers was observed with laser scanning confocal microscopy (LSCM) and field emission scanning electron microscopy (FESEM). Three key outcomes of this study provide new insights on the use of siliceous limestone in cement production, namely that (i) reducing the fineness values of siliceous limestone from 15% to 0% of residue on a 0.08 mm sieve decreases the quantity of these larger quartz particles, resulting in an increase in C3S content by up to 8% and an increase in 28d compressive strength by up to 4.4 Mpa, which is 62.30 Mpa; (ii) the morphology of quartz—either as chert nodules or single crystals—affects the microstructure of C2S clusters in clinker, finding that chert nodules result in clusters with more intermediate phases, whereas large single crystals lead to denser clusters; (iii) the sufficient fineness values of siliceous limestone SL1 and SL2 are 5% and 7% of residue on a 0.08 mm sieve, respectively, which can produce a clinker with a 28d compressive strength greater than 60 Mpa, indicating that for different kinds of quartz in siliceous limestone, there is an optimum grinding solution that can achieve a balance between clinker quality and energy consumption without having to grind siliceous limestone to very fine grades.

Effect of CuO on the Burnability and Mineral Formation of High C3S Cement Clinker

Effect of CuO on the Formation of Clinker Minerals and the Hydration Properties

Effect of Tio2 on the Formation of Clinker with High C3s

The effect of the combined addition of copper, lithium and sulphur on the formation of Portland cement clinker

Utilization of Coal Gangue and Copper Tailings As Clay for Cement Clinker Calcinations

Effect of Steel Slag on Burnality of Cement Raw Meal

Effects of Fineness and Morphology of Quartz in Siliceous Limestone on the Calcination Process and Quality of Cement Clinker

Synthesis and Sintering Reaction Mechanism of High-Performance MgO-CaO-Fe2O3 Clinker

Experimental study on the relationship between the mineral production capability and the physiochemical properties in the coproduction of Q phase-3CaO·3Al2O3·CaSO4 cement clinker

Effect of Foreign Oxide on the Burnability of Cement Raw Meal with High CaO

Effect of CaO Sourced from CaCO3 or CaSO4 on Phase Formation and Mineral Composition of Iron-Rich Calcium Sulfoaluminate Clinker

Influence of CaO on Physical and Environmental Properties of Granulated Copper Slag: Melting Behavior, Grindability and Leaching Behavior

Thermodynamic Analysis on Mineral Formation of Q-phase Cement Clinkers Cogenerated from Low-sulfur Coal Combustion

The Roles of B<sub>2</sub>O<sub>3</sub> and P<sub>2</sub>O<sub>5</sub> in the Formation of Cement Clinker

Effects of clinker contents of different C3A and C4AF on the performance of PSC cement

Research on the Hydration Properties of C4A3S-CSH2 Cement System at Different Temperatures

Low-Temperature Calcination of Belite-Calcium Sulphoaluminate Cement Clinker and the Hydration Process

Influence of Cu Doping on the Hydration of Dicalcium Silicate: A First-Principles Study

Experimental Study on Factors Influencing Coproduction of Q-phase Cement Clinker by Pulverized Coal Fired Boilers

Effect of Residual CaSO4 in Clinker on Properties of High Belite Sulfoaluminate Cement Based on Solid Wastes

Thermochemical behavior of several common salts blended with cement raw material