Abstract:With the increasing depletion of high-quality raw materials, siliceous limestone, sandstone and other hard-to-burn raw materials containing crystalline SiO2 are gradually being used to produce clinker. This study investigates the influence of the quartz content and particle size in siliceous limestone on the calcination process and the resultant quality of cement clinker. Two different siliceous limestones were grinded to different fineness, and calcinated with some other materials. The content of the clinkers was analyzed with the XRD–Rietveld method and the microstructure of the clinkers was observed with laser scanning confocal microscopy (LSCM) and field emission scanning electron microscopy (FESEM). Three key outcomes of this study provide new insights on the use of siliceous limestone in cement production, namely that (i) reducing the fineness values of siliceous limestone from 15% to 0% of residue on a 0.08 mm sieve decreases the quantity of these larger quartz particles, resulting in an increase in C3S content by up to 8% and an increase in 28d compressive strength by up to 4.4 Mpa, which is 62.30 Mpa; (ii) the morphology of quartz—either as chert nodules or single crystals—affects the microstructure of C2S clusters in clinker, finding that chert nodules result in clusters with more intermediate phases, whereas large single crystals lead to denser clusters; (iii) the sufficient fineness values of siliceous limestone SL1 and SL2 are 5% and 7% of residue on a 0.08 mm sieve, respectively, which can produce a clinker with a 28d compressive strength greater than 60 Mpa, indicating that for different kinds of quartz in siliceous limestone, there is an optimum grinding solution that can achieve a balance between clinker quality and energy consumption without having to grind siliceous limestone to very fine grades.

Effect of Tio2 on the Formation of Clinker with High C3s

Effect of CuO on the Burnability and Mineral Formation of High C3S Cement Clinker

Effect of CuO on the Formation of Clinker Minerals and the Hydration Properties

The Roles of B<sub>2</sub>O<sub>3</sub> and P<sub>2</sub>O<sub>5</sub> in the Formation of Cement Clinker

INFLUENCE OF ALUMINA MODULUS AND LIQUID PROPERTIES ON BURNING PROCESS OF TRICALCIUM SILICATE-RICH PORTLAND CLINKERS

Synthesis and Sintering Reaction Mechanism of High-Performance MgO-CaO-Fe2O3 Clinker

The effect of the combined addition of copper, lithium and sulphur on the formation of Portland cement clinker

Improving the Comprehensive Properties of ZrO2–C Materials with Aid of TiO2 Addition

Effects of Chromium Addition on Preparation and Properties of Bulk Cementite

Effect of Er2O3 addition and calcining temperature on CaTiO3 material prepared by solid reaction

Effects of sulfur on the solidification of cadmium during clinkerization

Effect of CeO2 Addition on Sintering Property and Microstructure of CaTiO3 Ceramics

Effect of Steel Slag on Burnality of Cement Raw Meal

Thermochemical behavior of several common salts blended with cement raw material

Effect of Fe on the Phases and Microstructure of TiC–Fe Cermets by Combustion Synthesis/quasi-Isostatic Pressing

Influence of Basicity and TiO2 Content on the Precipitation Behavior of the Ti-bearing Blast Furnace Slags

The Effects of Incomplete Combustion on Ba2Ti9O20 Phase Formation in a Citrate Solution Combustion Method

Effects of different Ti/C and Al contents on combustion synthesized Ti3AlC2 powders in the Ti-Al-C system

Effects of different Al contents on combustion synthesis of Ti3AlC2 powders in the Ti-Al-C system

Effect of CaO Sourced from CaCO3 or CaSO4 on Phase Formation and Mineral Composition of Iron-Rich Calcium Sulfoaluminate Clinker

Effects of Fineness and Morphology of Quartz in Siliceous Limestone on the Calcination Process and Quality of Cement Clinker