Laser Frequency Noise Limited Sensitivity In A Resonator Optic Gyroscope

Huilian Ma,Xu Chang,Hui Mao,Zhonghe Jin

2010-01-01

Abstract:The laser frequency noise limited sensitivity in a resonator optic gyroscope due to an intermodulation effect is first demonstrated. A bias stability of 0.055 deg/s is best demonstrated in a resonator micro optic gyroscope.

What problem does this paper attempt to address?

Reduction of High-Frequency Laser Noise in Resonant Fiber Optic Gyroscope with a Phase-Modulated Feedback Loop

Sen Ye,Yi Lin,Hanzhao Li,Huihan Ma,Zhonghe Jin

DOI: https://doi.org/10.1109/icocn.2017.8121535

2017-01-01

Abstract:The resonant fiber-optic gyroscope (RFOG) based on the Sagnac effect is a high-accuracy rotation sensor. The intermodulation error due to the laser noise at even harmonics of the modulation frequency deteriorates the performance of the RFOG. Aiming at the suppression of high-frequency laser noise, a phase-modulated feedback loop is developed and analyzed. The parameters of the servo loop is optimized to enhance the performance of the gyroscope.
Research on Frequency Stability of Narrow Linewidth Laser in Resonant Optical Gyro

Kang Zou,Ran Bi,Kan Chen,Xuan She,Caini Zhang,Xiaowu Shu

DOI: https://doi.org/10.1016/j.yofte.2020.102403

IF: 2.8

2021-01-01

Optical Fiber Technology

Abstract:In this study, to measure the frequency drift characteristics of the narrow-linewidth laser, we provide a method with high accuracy and adjustable measuring range that can be applied in a resonant optical gyro (ROG) system. In an ROG system, the laser frequency drift characteristics, such as fluctuation range and frequency, influence the performance of the closed-loop frequency-locked module. To measure the above performance of the laser, we proposed a novel measurement system based on the Fabry-Perot cavity. We proved the feasibility of the scheme through theory and simulation. Then, the calibration of the experimental device and the measurement of the tested laser were completed. The measurement accuracy of this method is 1.2 kHz, and the measurement range reaches +/- 60 MHz, which can be adjusted by the modulation index. The results show that the laser has a frequency fluctuation of 30 MHz in the stabilization stage, and there is mainly a low-frequency component under 5 Hz in the frequency domain of the laser frequency fluctuation. Furthermore, this measurement scheme can be applied in other fiber sensor systems to evaluate the effect of laser frequency fluctuation on system output performance.
Laser Frequency Noise Measurement in a Resonant Fiber Optic Gyro

Guhong Zhang,Zhuoqun Yu,Zhaobin Xu,Zhonghe Jin

DOI: https://doi.org/10.1016/j.ijleo.2018.08.129

IF: 3.1

2018-01-01

Optik

Abstract:A resonant fiber optic gyro (RFOG) is a high-accuracy inertial rotation sensor based on the Sagnac effect. Knowledge of the laser frequency noise, especially the study of its transfer characteristics is critical to optimize the resonant frequency servo loop parameters in the RFOG. In this paper, a Mach–Zehnder interferometer (MZI) is used to measure the changes of the power spectral density (PSD) of the laser frequency noise. Three different observation points are set to investigate the transfer characteristics of the laser beam along the transmission loop of the RFOG. Through real-time observation and analysis of the PSDs of the laser frequency noise, we found that the effects of the laser frequency noise on the RFOG can be clearly determined, and the resonant frequency servo loop parameters can be optimized according to the required gyro bandwidth. We also demonstrate the significance of reducing the residual error at the lock-in frequency while ensuring a sufficient gyro bandwidth.
Influence of intensity noise on the resonant fiber optic gyroscope and restraining

Yijia Gong,Ran Bi,Heliang Shen,Kang Zou,Kan Chen,Xiaowu Shu

DOI: https://doi.org/10.1016/j.optcom.2021.127074

IF: 2.4

2021-01-01

Optics Communications

Abstract:In a resonant fiber optical gyroscope (RFOG) system, the imperfection of light intensity is primarily categorized into two parts: intensity fluctuation and inconsistent power of two paths. Firstly, the error of the intensity fluctuation effect on the RFOG scale factor is presented and simulated. Secondly, the RFOG bias drift caused by the Kerr effect is simulated when the intensity fluctuates. Next, an RFOG system with the servo of intensity stable is proposed. Experimental results confirm that the intensity fluctuation of the two paths is effectively suppressed, and the Kerr effect error can be effectively eliminated. Finally, the light intensity stability improves more than 30 dB, the RFOG bias stability decreases at least 6 dB, and the scale factor nonlinearly is suppressed by 20 dB.
Evaluation and Suppression of the Effect of Laser Frequency Noise on Resonant Fiber Optic Gyroscope

Lu Liu,Hanzhao Li,Huilian Ma,Zhonghe Jin

DOI: https://doi.org/10.1109/jlt.2021.3135120

IF: 4.7

2021-01-01

Journal of Lightwave Technology

Abstract:This article provides a novel method to analyze and calculate the effect of laser frequency noise on a resonant fiber optic gyroscope (RFOG). The output signal of the fiber ring resonator is expressed as the sum of various harmonic responses. It is found that the laser frequency noise at certain noise frequency would be demodulated together with the rotation-induced frequency signal, and thus deteriorating the gyro output stability. A theoretical model is then setup. The effect of laser frequency noise on the RFOG based on the separate modulation-demodulation technique is numerically evaluated and the effectiveness of the reciprocal modulation-demodulation technique is verified both theoretically and experimentally. The measured angular random walk of the reciprocal RFOG improves as the detected light power at the photodetector increases, which indicates that the measured angular random walk reaches the theoretical shot-noise limited sensitivity in the RFOG. The best value is 0.0021 °/√h when the light power arrived at the photodetector is 69 μW.
Laser frequency noise induced error in resonant fiber optic gyro due to an intermodulation effect.

Huilian Ma,Yuchao Yan,Linglan Wang,Xu Chang,Zhonghe Jin

DOI: https://doi.org/10.1364/OE.23.025474

IF: 3.8

2015-01-01

Optics Express

Abstract:For the first time, a significant noise source in the resonant fiber optic gyroscope (RFOG) called intermodulation induced error is proposed and deeply analyzed in this paper. The intermodulation error is produced by the laser frequency noise at even multiples of the modulation frequency due to an intermodulation effect, which will seriously limit the random noise performance of the RFOG. Experiments are designed and conducted to verify and measure the intermodulation induced error in the RFOG. The experimental results confirm the existence of intermodulation error, and fit well with the theory. As for the design of the RFOG, light sources with a narrow intrinsic linewidth and a high modulation frequency are preferable to achieve a high rotation-rate sensitivity. (C) 2015 Optical Society of America
Frequency Noise Characteristics of A Narrow-Linewidth Dfb Semiconductor Laser in Resonator Fiber Optic Gyro

Guhong Zhang,Huilian Ma,Zhonghe Jin

DOI: https://doi.org/10.1117/12.975216

2012-01-01

Abstract:It is important to study the frequency noise of the laser characteristics in a resonator fiber optic gyro. A measurement of the power spectral density of optic frequency noise is introduced into a resonator fiber optic gyro. An optic optimum criterion for the frequency stabilization loop of the resonator fiber optic gyro is proposed, especially for the reduction of the locking residual error and the widening of the gyro bandwidth.
Laser Frequency Noise Power Spectral Density Measurement Technology and Its Application to Resonant Optical Fiber Gyroscope

Liu Shuang,Li Hanzhao,Liu Lu,Qian Weiwen,Lin Yi,Ma Huilian

DOI: https://doi.org/10.3788/aos202141.1306010

2021-01-01

Acta Optica Sinica

Abstract:A resonant optical fiber gyroscope (RFOG) is an optical sensor that measures the angular rate of rotation proportional to the difference between the resonant frequency of the clockwise and counterclockwise optical paths generated by the Sagnac effect. A narrow linewidth laser with a continuously adjustable center frequency is a key element for developing RFOG, and the frequency noise characteristics of the laser directly affect the performance of this gyroscope. In this study, the frequency noise power spectral density of different types of lasers and the lasers before and after frequency locking was measured using an unbalanced Mach-Zehnder interferometer system based on a 3X3 coupler. The 1/f and white noise characterization coefficients of different types of lasers and the lasers before and after frequency locking were obtained. The study results can provide an important reference for selecting RFOGs with different accuracies and optimizing resonant frequency servo loops.
An Open-Loop RFOG Based on Harmonic Division Technique to Suppress LD's Intensity Modulation Noise

Diqing Ying,Zeyu Wang,Jianmin Mao,Zhonghe Jin

DOI: https://doi.org/10.1016/j.optcom.2016.05.056

IF: 2.4

2016-01-01

Optics Communications

Abstract:A harmonic division technique is proposed for an open-loop resonator fiber optic gyro (RFOG) to suppress semiconductor laser diode's (LD's) intensity modulation noise. The theoretical study indicates the RFOG with this technique is immune to the intensity noise. The simulation and experimental results show this technique would lead to a diminished linear region, which still could be acceptable for an RFOG applied to low rotation rate detection. The tests for the gyro output signal are carried out with/without noise suppressing methods, including the harmonic division technique and previously proposed signal compensation technique. With the harmonic division technique at the rotation rate of 10deg/s, the stability of gyro output signal is improved from 1.07deg/s to 0.0361deg/s, whose noise suppressing ratio is more than 3 times as that of the signal compensation technique. And especially, a 3.12deg/s signal jump is significantly removed with the harmonic division technique; in contrast, a residual 0.36deg/s signal jump still exists with the signal compensation technique. It is concluded the harmonic division technique does work in intensity noise suppressing under dynamic condition, and it is superior to the signal compensation technique.
Resonator Fiber Optic Gyro Employing a Semiconductor Laser.

Zhonghe Jin,Xuhui Yu,Huilian Ma

DOI: https://doi.org/10.1364/ao.51.002856

IF: 1.9

2012-01-01

Applied Optics

Abstract:Resonator fiber optic gyro (RFOG) based on the Sagnac effect has the potential to achieve the inertial navigation system requirement with a short sensing coil. Semiconductor laser is one of the key elements for integration and miniaturization of the RFOG. In this paper, an RFOG employing a semiconductor laser is demonstrated. The model of the laser frequency noise induced error in the RFOG is described. To attenuate the laser frequency noise induced error, active frequency stabilization is applied. An online laser frequency noise observation is built, as a powerful optimum criterion for the loop parameters. Moreover, the laser frequency noise observation method is developed as a new measurement tool. With a fast digital proportional integrator based on a single field programmable gate array applied in the active stabilization loop, the laser frequency noise is reduced to 0.021 Hz (1σ). It is equivalent to a rotation rate of 0.07°/h, and close to the shot noise limit for the RFOG. As a result, a bias stability of open-loop gyro output is 9.5°/h (1σ) for the integration time 10 s in an hour observed in the RFOG. To the best of our knowledge, this result is the best long-term stability using the miniature semiconductor laser.
Open-loop Operation Experiments in a Resonator Fiber-Optic Gyro Using the Phase Modulation Spectroscopy Technique.

Xu-lin Zhang,Hui-lian Ma,Zhong-he Jin,Chun Ding

DOI: https://doi.org/10.1364/ao.45.007961

IF: 1.9

2006-01-01

Applied Optics

Abstract:A detection system in the resonator fiber-optic gyro is set up by the phase modulation (PM) spectroscopy technique. The slope of the demodulated curve near the resonant point is found to affect the ultimate sensitivity of the gyro. To maximize the demodulated signal slope, the modulation frequency and index are optimized by the expansion of the Bessel function and optical field overlapping method. Using different PM frequencies for the light waves, the open-loop gyro output signal is observed. The modulation frequency in this PM technique is limited only by the cutoff frequency of the LiNbO3 phase modulators, which can reach several gigahertz. This detection technique and system can be applied to the resonator micro-optic gyro with a less than 10 cm long integrated optical ring.
How Laser Diode (LD) Intensity Modulation Induced by Current Tuning Affects the Performance of an Open-loop Resonator Fibre Optic Gyro (R-FOG) with Sinusoidal Wave Modulation

D. Ying,Q. Li,H. Ma,Z. Jin

2014-01-01

Lasers in Engineering

Abstract:We present how the laser diode (LD) current tuning induced intensity modulation affects the performance of an open-loop resonator fibre optic gyro (R-FOG) with sinusoidal wave modulation. The expression for the demodulation curve under intensity modulation caused by the dynamic input rotation angular rate and varied environmental factors induced resonance frequency drift is provided. Numerical investigation shows that under the intensity modulation effect due to dynamic input rotation angular rate, which results in a bending trend for the linear part of demodulation curve, the linearity of R-FOG system is deteriorated, and the scale factor nonlinearity of gyro output increases as the frequency-intensity conversion coefficient of the LD increases. By simulating the demodulation curve with different amount of resonance frequency drift due to varied environmental factors, the slope of the linear part is found to fluctuate under the resonance frequency drift induced intensity modulation, and it causes the scale factor of the practical R-FOG system to fluctuates. This scale factor fluctuation results in a system measurement error, which is proven to increase as the amount of resonance frequency drift or input rotation angular rate increases, and numerical calculation result shows this large system error should be counted for an open-loop R-FOG system.
Resonator micro-optic gyroscope based on the double phase modulation technique

Hui Mao,Huilian Ma,Zhonghe Jin

DOI: https://doi.org/10.1364/cleo.2010.jwa52

2010-01-01

Abstract:Double phase modulation technique is presented to relax the accuracy of the modulation index. A bias stability of 3.14×10-3 rad/s is demonstrated in a resonator micro-optic gyro with the silica waveguide ring length of 7.9 cm. © 2009 Optical Society of America.
Characteristic Analysis of Noise in a Resonator Optic Gyroscope (ROG) Using a Feedback Loop

D. Ying,Q. Li,Y. Ren,H. Ma,Z. Jin,W. Wu

2015-01-01

Lasers in Engineering

Abstract:We set up a broadened resonator optic gyroscope (ROG) feedback loop model with the noise sources including a standard data acquisition (DAQ) board induced electric circuit noise, photo-detector (PD) noise and laser frequency noise, to predict, explain, and further optimize the system performance. Based on this model and combining with experimental tests, the characteristics of these three noises in ROG is analysed and optimized, and how the noises transfer in feedback state is discussed. The system with feedback loop shows strong rejection to electric circuit noise and laser frequency noise in the system output bandwidth, but nearly no effect on the power of PI) noise. For the whole noise power spectrum, larger loop delay and system output bandwidth induces more power for all the three noise sources, and larger loop gain induces less power for both electric circuit and laser frequency noises but more power for PI) noise. The sum of the three noises equivalent rotation is predicted and optimized by choosing different loop gain, loop delay and output bandwidth, and it is concluded that for a resonator micro-optic gyroscope (RMOG) with a 7.9 cm perimeter resonator, if the system loop delay decreases to 1 mu s and gain increases to 1.6 x 10(7), the noise equivalent rotation caused by laser frequency noise and PD noise will be down to 2.66 degrees/h with 10.00 Hz output bandwidth.
Full Investigation of the Resonant Frequency Servo Loop for Resonator Fiber-Optic Gyro.

Huilian Ma,Xiao Lu,Linzhi Yao,Xuhui Yu,Zhonghe Jin

DOI: https://doi.org/10.1364/ao.51.005178

IF: 1.9

2012-01-01

Applied Optics

Abstract:Resonator fiber-optic gyro (RFOG) is a high-accuracy inertial rotation sensor based on the Sagnac effect. A high-accuracy resonant frequency servo loop is indispensable for a high-performance RFOG. It is composed of a frequency discriminator, a loop filter, and a laser actuator. Influences of the loop parameters are fully developed. Optimized loop parameters are obtained by considering the noise reduction and wide dynamic performance of the RFOG. As a result, with the integration time of 10 s, the accuracy of the resonant frequency loop is increased to 0.02 Hz (1σ). It is equivalent to a rotation rate of 0.067°/h, which is close to the shot noise limit for the RFOG, while a minimum rotation of ±0.05°/s has been carried out simultaneously. These are the best results reported to date, to the best of our knowledge, for an RFOG using the miniature semiconductor laser that benefits from the optimization of the resonant frequency servo-loop parameters.
Reduction of relative intensity noise in a broadband source-driven RFOG using a high-frequency modulation technique

Shuang Liu,Lu Liu,Junyi Hu,Qingwen Liu,Huilian Ma,Zuyuan He

DOI: https://doi.org/10.1364/OL.470933

IF: 3.6

2022-01-01

Optics Letters

Abstract:A broadband source-driven resonant fiber-optic gyroscope (RFOG) can reduce coherence-related noise, thus achiev-ing a better sensitivity with a much simpler configuration than the traditional system with a coherent source. Its detection sensitivity, however, is still limited by the excess relative intensity noise (RIN) of the broadband source. In this paper, the RIN error mechanism in this broadband source-driven RFOG is revealed and countermeasures are presented. We demonstrate that the use of a high-finesse fiber-optic ring resonator and a high-frequency modulation -demodulation technique can reduce the RIN-induced error. It is indicated that the optimal modulation parameters can provide a RIN-induced error reduction of 6.1 dB, allowing the broadband source-driven RFOG to operate near the shot-noise-limited theoretical sensitivity. With the optimal high-frequency modulation-demodulation technique, an angle random walk of 0.0013 degrees/root h is achieved with a 200-m -long fiber-optic ring resonator of 7.6 cm diameter. This is the best result reported to date, to the best of our knowledge, for fiber-optic gyroscopes of this size. (C) 2022 Optica Publishing Group
Precision Analysis of Frequency Lock-in Technique in Resonator Micro Optic Gyroscope

BAO Hui-qiang,MAO Hui,MA Hui-lian,JIN Zhong-he

DOI: https://doi.org/10.3785/j.issn.1008-973x.2010.01.017

2010-01-01

Abstract:In resonator micro optic gyro (R-MOG) system, optical elements, which are easily affected by environmentally-induced thermal and strain perturbations, induce various noises which restrict the preci-sion of lock-in frequency. Instead of the first-order inertia link, proportion integration (PI) controller was adopted in the feedback loop to reduce these noises and then improve the lock-in precision. An analytical model was setup, and the influences of the first-order inertia link and PI controller on the accuracy of lock-in frequency were analyzed and compared. PI controller technique can remove the steady-state error of the step response, so it can reduce the influence of the reciprocal noises by the environmentally-induced ther-mal and strain perturbations. The parameters of PI controller were optimized through simulation. Using the optimized PI controller in R-MOG system, the threshold for the lock-in frequency of 30 Hz was achieved; which was equivalent to the rotation sensitivity of 0.15°/s for an R-MOG with a 7.9 cm length micro ring resonator chip. Gyro rotation signal at 20°/s is best demonstrated in the above mentioned R-MOG system.
A Miniaturized Compact Open-Loop RFOG with Demodulation Signal Compensation Technique to Suppress Intensity Modulation Noise

Diqing Ying,Jianmin Mao,Qiang Li,Zhonghe Jin

DOI: https://doi.org/10.1016/j.optcom.2015.10.006

IF: 2.4

2016-01-01

Optics Communications

Abstract:A miniaturized compact open-loop resonator fiber optic gyro (RFOG) prototype with main body size of about 10.4cm×10.4cm×5.2cm is reported, and a demodulation signal compensation technique is proposed, aiming to suppress the drift arising from accompanying intensity modulation induced by semiconductor laser diode (LD). The scheme of how to establish this miniaturized RFOG prototype is specifically stated. The linear relationship between the first-harmonic and second-harmonic demodulated signals respectively for the two counter propagating beams in the resonator is verified by theory and experiment, and based on this relationship, the demodulation signal compensation technique by monitoring the second-harmonic demodulated signal is described in detail. With this compensation technique, the gyro output stability under 1°/s rotation rate is effectively improved from 0.12°/s to 0.03°/s, and especially, an about 0.36°/s peak-to-peak fluctuation due to tuning current reset is significantly suppressed. A long term bias stability of about 4.5°/h in 1h for such a small-sized RFOG prototype is demonstrated, which is of the same magnitude as that of currently reported large-sized RFOG systems utilizing LD as the laser source as well.
Short Fiber Resonant Optic Gyroscope Using the High-Frequency Pound-Drever-Hall Technique.

Xiaojun Jin,Yi Lin,Ying Lu,Huilian Ma,Zhonghe Jin

DOI: https://doi.org/10.1364/ao.57.005789

IF: 1.9

2018-01-01

Applied Optics

Abstract:Optical gyros are attractive angular rotation sensors based on the Sagnac effect. The phase modulation technique is adopted to detect the weak resonant frequency shift induced by the Sagnac effect, which determines the detection sensitivity of the gyros. The Pound-Drever-Hall (PDH) modulation is a mature laser frequency stabilization technique that is widely recognized. A resonant optic gyro equipped with a short and high-finesse fiber ring resonator employing the high-frequency PDH modulation technique is proposed and demonstrated. The modulation index and frequency are optimized to maximize the slope of the demodulation curve. Compared with the low-frequency modulation, the high-frequency PDH modulation increases the slope of the demodulation curve by a factor of 1.23 and achieves an extra 15.8 dB of laser frequency noise suppression. The bias stability of the gyro output is improved from 9.6°/h to 8°/h, and the equivalent lock-in frequency accuracy increases 12 dB.
An Open-Loop Test of a Resonator Fiber Optic Gyro

Xulin Zhang,Huilian Ma,Zhonghe Jin,Chun Ding

DOI: https://doi.org/10.3969/j.issn.1674-4926.2006.04.020

2006-01-01

Abstract:The resonator fiber optic gyro (R-FOG) ,which utilizes a resonance frequency change due to the Sagnac effect,is a promising candidate for the next generation inertial rotation sensor. In this study,an open-loop R-FOG is set up using phase modulation spectroscopy. First,the demodulation curve is obtained using a lock-in amplifier.From the demodulation signal,a gyro dynamic range of ± 4. 2rad/s is obtained. Then,using different phase modulation frequencies,the open-loop gyro output signal is measured when the gyro is rotated clockwise or counterclockwise. The bias drift as a function of time is also measured. The fluctuation of the output over 5s is about 0. 02rad/s. The drift can be reduced by taking countermeasures against system noise.

Laser Frequency Noise Limited Sensitivity In A Resonator Optic Gyroscope

Reduction of High-Frequency Laser Noise in Resonant Fiber Optic Gyroscope with a Phase-Modulated Feedback Loop

Research on Frequency Stability of Narrow Linewidth Laser in Resonant Optical Gyro

Laser Frequency Noise Measurement in a Resonant Fiber Optic Gyro

Influence of intensity noise on the resonant fiber optic gyroscope and restraining

Evaluation and Suppression of the Effect of Laser Frequency Noise on Resonant Fiber Optic Gyroscope

Laser frequency noise induced error in resonant fiber optic gyro due to an intermodulation effect.

Frequency Noise Characteristics of A Narrow-Linewidth Dfb Semiconductor Laser in Resonator Fiber Optic Gyro

Laser Frequency Noise Power Spectral Density Measurement Technology and Its Application to Resonant Optical Fiber Gyroscope

An Open-Loop RFOG Based on Harmonic Division Technique to Suppress LD's Intensity Modulation Noise

Resonator Fiber Optic Gyro Employing a Semiconductor Laser.

Open-loop Operation Experiments in a Resonator Fiber-Optic Gyro Using the Phase Modulation Spectroscopy Technique.

How Laser Diode (LD) Intensity Modulation Induced by Current Tuning Affects the Performance of an Open-loop Resonator Fibre Optic Gyro (R-FOG) with Sinusoidal Wave Modulation

Resonator micro-optic gyroscope based on the double phase modulation technique

Characteristic Analysis of Noise in a Resonator Optic Gyroscope (ROG) Using a Feedback Loop

Full Investigation of the Resonant Frequency Servo Loop for Resonator Fiber-Optic Gyro.

Reduction of relative intensity noise in a broadband source-driven RFOG using a high-frequency modulation technique

Precision Analysis of Frequency Lock-in Technique in Resonator Micro Optic Gyroscope

A Miniaturized Compact Open-Loop RFOG with Demodulation Signal Compensation Technique to Suppress Intensity Modulation Noise

Short Fiber Resonant Optic Gyroscope Using the High-Frequency Pound-Drever-Hall Technique.

An Open-Loop Test of a Resonator Fiber Optic Gyro