Resonator micro-optic gyroscope based on the double phase modulation technique

Hui Mao,Huilian Ma,Zhonghe Jin

DOI: https://doi.org/10.1364/cleo.2010.jwa52

2010-01-01

Abstract:Double phase modulation technique is presented to relax the accuracy of the modulation index. A bias stability of 3.14×10-3 rad/s is demonstrated in a resonator micro-optic gyro with the silica waveguide ring length of 7.9 cm. © 2009 Optical Society of America.

What problem does this paper attempt to address?

Polarization maintaining silica waveguide resonator optic gyro using double phase modulation technique.

Hui Mao,Huilian Ma,Zhonghe Jin

DOI: https://doi.org/10.1364/OE.19.004632

IF: 3.8

2011-01-01

Optics Express

Abstract:Resonator micro optic gyro (RMOG) is a promising candidate for applications requiring small, light and robust gyros. In optical passive ring resonator gyros, clockwise and counter clockwise lightwaves are modulated at different frequencies to reduce the backscattering induced noise. The effectiveness of this technique, however, is determined by the carrier suppression level. Accurate modulation index and high environmental temperature stability is required for achieving high total carrier suppression for the traditional single phase modulation technique (SPMT). In this paper, we propose an RMOG based on the double phase modulation technique (DPMT). Compared with the traditional SPMT, two additional phase modulations are added to provide additional carrier suppression. It is found that the control accuracy of the modulation index and temperature stability is relaxed more than 30 times. It is easily performed for reducing the backscattering error below the shot noise limited sensitivity. The modulation parameters in the DPMT are analyzed and optimized. Based on the optimum parameters of the DPMT, a bias stability of 1.85 x 10(-4) rad/s is successfully demonstrated in the polarization maintaining silica waveguide resonator with the length of 7.9 cm. This is the best result reported to date, to the best of our knowledge, for a waveguide type passive ring resonator gyro. (C) 2011 Optical Society of America
Double Closed-Loop Resonant Micro Optic Gyro Using Hybrid Digital Phase Modulation.

Huilian Ma,Jianjie Zhang,Linglan Wang,Zhonghe Jin

DOI: https://doi.org/10.1364/oe.23.015088

IF: 3.8

2015-01-01

Optics Express

Abstract:It is well-known that the closed-loop operation in optical gyros offers wider dynamic range and better linearity. By adding a stair-like digital serrodyne wave to a phase modulator can be used as a frequency shifter. The width of one stair in this stair-like digital serrodyne wave should be set equal to the optical transmission time in the resonator, which is relaxed in the hybrid digital phase modulation (HDPM) scheme. The physical mechanism for this relaxation is firstly indicated in this paper. Detailed theoretical and experimental investigations are presented for the HDPM. Simulation and experimental results show that the width of one stair is not restricted by the optical transmission time, however, it should be optimized according to the rise time of the output of the digital-to-analogue converter. Based on the optimum parameters of the HDPM, a bias stability of 0.05°/s for the integration time of 400 seconds in 1 h has been carried out in an RMOG with a waveguide ring resonator with a length of 7.9 cm and a diameter of 2.5 cm.
A Hollow-Core Photonic-Crystal Fiber-Optic Gyroscope Based on a Parallel Double-Ring Resonator.

Heliang Shen,Kan Chen,Kang Zou,Yijia Gong,Ran Bi,Xiaowu Shu

DOI: https://doi.org/10.3390/s21248317

IF: 3.9

2021-01-01

Sensors

Abstract:A novel system structure of resonant fiber optical gyroscope using a parallel double hollow-core photonic crystal fiber ring resonator is proposed, which employs the double closed loop and reciprocal modulation–demodulation technique to solve the problem of the length mismatch between rings. This structure can suppress the residual amplitude modulation noise and laser frequency noise, essentially eliminating the influence of the Rayleigh backscattering noise and dramatically reduce the Kerr-effect-induced drift by three orders of magnitude. Thanks to its excellent noise suppression effect, the sensitivity of this novel system can approach the shot-noise-limited theoretical value of 8.94 × 10−7 rad/s assuming the length of the fiber ring resonator is 10 m.
Performance of Closed-Loop Resonant Micro Optic Gyro with Hybrid Digital Phase Modulation

Jianjie Zhang,Linglan Wang,Huilian Ma,Zhonghe Jin

DOI: https://doi.org/10.1117/12.2184125

2015-01-01

Abstract:A double closed-loop resonant micro optic gyro (RMOG) employing a hybrid digital phase modulation technique is demonstrated, showing encouraging progress. In this hybrid modulation scheme, the width of one stair of the stair-like digital serrodyne wave is optimized according to the rise time of the digital-to-analogue converter to obtain the maximum sideband suppression. Based on the optimum parameters of the hybrid modulation scheme, a typical bias stability of 0.05 degrees/s in 1 hr is demonstrated in an RMOG with a silica waveguide ring resonator having a ring length of 7.9 cm. This is the best long-term performance which has ever been reported in an RMOG to our knowledge.
Open-loop Operation Experiments in a Resonator Fiber-Optic Gyro Using the Phase Modulation Spectroscopy Technique.

Xu-lin Zhang,Hui-lian Ma,Zhong-he Jin,Chun Ding

DOI: https://doi.org/10.1364/ao.45.007961

IF: 1.9

2006-01-01

Applied Optics

Abstract:A detection system in the resonator fiber-optic gyro is set up by the phase modulation (PM) spectroscopy technique. The slope of the demodulated curve near the resonant point is found to affect the ultimate sensitivity of the gyro. To maximize the demodulated signal slope, the modulation frequency and index are optimized by the expansion of the Bessel function and optical field overlapping method. Using different PM frequencies for the light waves, the open-loop gyro output signal is observed. The modulation frequency in this PM technique is limited only by the cutoff frequency of the LiNbO3 phase modulators, which can reach several gigahertz. This detection technique and system can be applied to the resonator micro-optic gyro with a less than 10 cm long integrated optical ring.
Synchronous In-Phase and Quadrature Demodulation Technique for Resonant Micro-Optic Gyroscope.

Chuanbin Wu,Yi Lin,Xiaojun Jin,Huilian Ma,Zhonghe Jin

DOI: https://doi.org/10.1364/ao.58.005050

IF: 1.9

2019-01-01

Applied Optics

Abstract:The phase modulation and demodulation technique is widely used in resonant optical gyroscopes to accurately detect resonance frequencies, which directly affect gyro sensitivity. In order to overcome the influences of the system phase fluctuations, an in-phase and quadrature (IQ) demodulation technique is introduced for a resonant micro-optic gyroscope (RMOG). The phase fluctuations in the RMOG are measured, and their influence on the demodulation slope at the resonance point is compared between the traditional sinusoidal demodulation and the IQ demodulation both theoretically and experimentally. It can be concluded that the output of the proposed IQ demodulation is not affected by any phase fluctuations. The demodulation slope is always at its maximum value, thus improving the signal-to-noise ratio of the detection system. By using the IQ demodulation technique, a random walk coefficient of 0.5°/√h is carried out. A long-term bias stability of 9°/h is successfully observed, which is improved by a factor of 1.6 compared with that obtained using the traditional phase-sensitive sinusoidal demodulation technique.
Waveguide-type Optical Passive Ring Resonator Gyro Using Phase Modulation Spectroscopy Technique

Huilian Ma,Xulin Zhang,Zhonghe Jin,Chun Ding

DOI: https://doi.org/10.1117/1.2280645

IF: 1.3

2006-01-01

Optical Engineering

Abstract:We report the first demonstration of silica waveguide optical passive ring resonator gyro (OPRG) based on the phase modulation spectroscopy technique. The ring resonator is composed of a 6-cm-long silica waveguide. Observed from the resonance curve, the free spectral range (FSR) of the resonator, the full width at half maximum (FWHM) of the resonance curve, the finesse (F) of the resonator, and the resonance depth are 3.4 GHz, 62 MHz, 54.8, and 70%, respectively. The detection sensitivity of this OPRG will be 7.3 X 10(-5) rad/s. In the experiments, there is an acoustic-optical modulator (AOM) in each light loop. We lock the lasing frequency at the resonance frequency of the silica waveguide ring resonator for counterclockwise (CCW) lightwave; the frequency difference between the driving frequencies of the two AOMs is equivalent to the Sagnac frequency difference caused by gyro rotation. Thus, the gyro output is observed. (c) 2006 Society of Photo-Optical Instrumentation Engineers.
Resonator micro optic gyro with double phase modulation technique using an FPGA-based digital processor

Zhonghe Jin,Guhong Zhang,Hui Mao,Huilian Ma

DOI: https://doi.org/10.1016/j.optcom.2011.11.017

IF: 2.4

2012-01-01

Optics Communications

Abstract:Experiments on resonator micro-optic gyro (RMOG) with a digital proportional integral (PI) feedback scheme are performed. In this experimental setup, the key rotation sensing element is a polarization maintaining silica waveguide ring resonator (WRR) with a ring length of 7.9cm and a diameter of 2.5cm. A good linearity of 0.0015% over a wide range of ±2×104°/s can be achieved for the RMOG theoretically. The optimal digital PI feedback scheme is adopted in the frequency servo loop to reduce the reciprocal frequency fluctuations due to the WRR resonance frequency and laser frequency drifts. Residual equivalent input fluctuation can be reduced as low as 0.03°/s/√Hz based on the optimal digital PI feedback scheme, which is close to the shot noise limited spectral density 0.02°/s/√Hz of the RMOG with the input optical power of 0.2mW. Relationship between RMOG output signal and angular rate is obtained from ±0.1°/s to ±5°/s. The standard deviation of the residuals between RMOG output results and linear fit curve is 0.066°/s. For an integration of the processing circuit, all the processing circuit is implemented by a field programmable gate array (FPGA) instead of instruments. The output of this digitalized RMOG is obtained over a range of ±550°/s. The linearity of this digitalized RMOG is 0.0169%.
Improving thermal stability of a closed-loop resonant fiber-optic gyroscope using a double demodulation technique

Lu Liu,Shuang Liu,Junyi Hu,Huilian Ma,Zhonghe Jin

DOI: https://doi.org/10.1109/ICOCN55511.2022.9900969

2022-01-01

Abstract:This paper presents the thermal stability improvement of a closed-loop resonant fiber-optic gyroscope using a reciprocal modulation and double demodulation technique, showing stable behavior with a bias stability of <tex xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">$0.3^{\mathrm{o}}/\mathrm{h}$</tex> in a temperature change.
Resonant fiber optic gyroscope using a reciprocal modulation and double demodulation technique

Lu Liu,Shuang Liu,Junyi Hu,Huilian Ma,Zhonghe Jin

DOI: https://doi.org/10.1364/OE.458596

IF: 3.8

2022-01-01

Optics Express

Abstract:A resonant fiber optic gyroscope (RFOG) using a reciprocal modulation and double demodulation technique based on a single laser source is proposed and demonstrated. The effect of the residual amplitude modulation of the phase modulator is well suppressed thanks to the reciprocal modulation and demodulation. On this basis, the backscattering noise is also eliminated by the double demodulation process. The long-term bias stability of the RFOG is successfully improved to 0.2 degrees/h for a test time of 45 hours. (C) 2022 Optica Publishing Group under the terms of the Optica Open Access Publishing Agreement
Resonant Fiber Optic Gyro Based on A Sinusoidal Wave Modulation and Square Wave Demodulation Technique

Linglan Wang,Yuchao Yan,Huilian Ma,Zhonghe Jin

DOI: https://doi.org/10.1364/ao.55.003274

IF: 1.9

2016-01-01

Applied Optics

Abstract:New developments are made in the resonant fiber optic gyro (RFOG), which is an optical sensor for the measurement of rotation rate. The digital signal processing system based on the phase modulation technique is capable of detecting the weak frequency difference induced by the Sagnac effect and suppressing the reciprocal noise in the circuit, which determines the detection sensitivity of the RFOG. A new technique based on the sinusoidal wave modulation and square wave demodulation is implemented, and the demodulation curve of the system is simulated and measured. Compared with the past technique using sinusoidal modulation and demodulation, it increases the slope of the demodulation curve by a factor of 1.56, improves the spectrum efficiency of the modulated signal, and reduces the occupancy of the field-programmable gate array resource. On the basis of this new phase modulation technique, the loop is successfully locked and achieves a short-term bias stability of 1.08°/h, which is improved by a factor of 1.47.
Synchronous Digital Quadrature Demodulation Technique For Resonant Optic Gyroscopes

Chuanbin Wu,Yi Lin,Sen Ye,Guhong Zhang,Huilian Ma,Zhonghe Jin

DOI: https://doi.org/10.1109/acp.2018.8596301

2018-01-01

Abstract:A synchronous digital quadrature demodulation technique for resonant optic gyroscopes is proposed. Both numerical and experimental results indicate that the demodulation curve of the system is insensitive to phase fluctuation, thus achieving high signal-to-noise ratio.
Signal processing improvement of passive resonant fiber optic gyroscope using a reciprocal modulation-demodulation technique

Hanzhao Li,Yi Lin,Lu Liu,Huilian Ma,Zhonghe Jin

DOI: https://doi.org/10.1364/OE.390605

IF: 3.8

2020-01-01

Optics Express

Abstract:A resonant fiber optic gyroscope (RFOG) based on the reciprocal phase modulation-demodulation technique is proposed and demonstrated. The residual amplitude modulation induced error of the phase modulator, and the effect of laser frequency noise are all suppressed thanks to the reciprocity of the proposed signal processing scheme. Compared with the past separate modulation-demodulation RFOG, the angular random walk is improved by a factor of 15 times from 0.08 degrees/root h to 0.0052 degrees/root h, and the bias stability is improved from 0.3 degrees/h to 0.06 degrees/h. (C) 2020 Optical Society of America under the terms of the OSA Open Access Publishing Agreement
Single-Polarization Fiber-Pigtailed High-Finesse Silica Waveguide Ring Resonator for A Resonant Micro-Optic Gyroscope

Jianjie Zhang,Huilian Ma,Hanzhao Li,Zhonghe Jin

DOI: https://doi.org/10.1364/ol.42.003658

IF: 3.6

2017-01-01

Optics Letters

Abstract:A new record for high-finesse silica waveguide ring resonators (WRRs), to the best of our knowledge, is demonstrated experimentally. The achieved finesse and resonant depths of the silica WRR with a length of 7.9 cm and a diameter of 2.5 cm are 196.7% and 98%, respectively. In addition, the silica WRR chip is coupled with single-polarization fiber to improve the polarization extinction ratio (PER) and, thus, to reduce the polarization error. With the application of this high-finesse and high-PER WRR to the resonant microoptic gyroscope (RMOG), a bias stability of 0.004 degrees/s is observed over a 1 h timeframe. To the best of our knowledge, this is the first RMOG reported in the open literature that can sense the earth's rotation rate (15 degrees/h). (C) 2017 Optical Society of America
High Finesse Silica Waveguide Ring Resonators for Resonant Micro-Optic Gyroscopes

Jianjie Zhang,Hanzhao Li,Huilian Ma,Zhonghe Jin

DOI: https://doi.org/10.1117/12.2263256

2017-01-01

Abstract:A high-finesse silica waveguide ring resonator (WRR) is designed and a new record is demonstrated experimentally. The finesse and the resonant depth of the silica WRR with a length of 7.9 cm and a diameter of 2.5 cm are 196.7 and 98%, respectively. In addition, the silica WRR is pigtailed with single-polarization fiber to improve the polarization extinction ratio thus to reduce the polarization error. With the application of this high-finesse and high polarization extinction ratio WRR to the resonant micro-optic gyroscope (RMOG), a bias stability of 0.004°/s was observed over a one-hour timeframe.
Resonator Fiber Optic Gyro Using the Triangle Wave Phase Modulation Technique

Diqing Ying,Huilian Ma,Zhonghe Jin

DOI: https://doi.org/10.1016/j.optcom.2007.10.012

IF: 2.4

2008-01-01

Optics Communications

Abstract:Based on the Sagnac effect, resonator fiber optic gyro (R-FOG) has potential as a high accuracy inertial rotation sensor. An R-FOG based on the triangle wave phase modulation technique is proposed in this paper. The slope of the demodulation curve near the resonance dip is found to affect the ultimate sensitivity of the gyro. In order to maximize the slope of the demodulation signal, the parameters of the triangle wave are analyzed. By employing Fourier series and the method of field overlapping, the relationship between the demodulation signal and the resonance frequency deviation is analyzed. The optimum values for the modulation frequency and phase modulation index are obtained. And the relationship between the carrier component and the phase modulation index under analysis in this paper shows that the triangle wave phase modulation technique is more advantageous than the traditional modulation technique in reducing the noise induced by backscattering. (c) 2007 Elsevier B.V. All rights reserved.
Polarization error in resonant micro-optic gyroscopewith different waveguide-type ring resonatorstructures

shuang Liu,Yi Lin,Xiaojun Jin,Huilian Ma,Zhonghe Jin

DOI: https://doi.org/10.1364/ao.457490

IF: 1.9

2022-01-01

Applied Optics

Abstract:The waveguide-type ring resonator (WRR) is the key rotation-sensing element in a resonant micro-optic gyroscope (RMOG). A universal model used to analyze both the polarization characteristics of the WRR and corresponding temperature-related polarization error in the RMOG is presented. It indicates that the polarization problem stems from the excitation of two polarization states within the WRR. Unequal variations of incident lights on the cavity in the two directions can cause bias errors at the RMOG output. With the application of different silica WRRs to the RMOG, the polarization errors are tested and verify the theoretical results. Finally, a segment of tilted waveguide gratings with Brewster's angle is fabricated on the silica waveguide within the cavity. The measured polarization extinction ratio of the output light from the WRR is as high as 35.2 dB. The corresponding temperature dependence of the polarization error is theoretically reduced to 0.0019 (degrees/s)/degrees C, which indicates that temperature control is sufficient for a tactical grade RMOG. (C) 2022 Optica Publishing Group
Resonator Fiber Optic Gyroscope with an All Digitalized System

Xuhui Yu,Huilian Ma,Jin, Zhonghe

DOI: https://doi.org/10.1109/isscaa.2010.5633090

2010-01-01

Abstract:Resonator fiber optic gyroscope has the potential to achieve the inertial navigation system requirement with a short sensing coil. An all digitalized system is constructed including the signal modulation/demodulation and a proportional integral (PI) controller in a single field programmable gate array. Under this scheme, the serrodyne phase modulation technique is adopted, which is of benefit to overcome the backscattering induced noise and easy to implement in closed-loop operation. The phase modulation index is optimized to achieve high carrier suppression. The PI controller is adopted in the frequency servo loop to eliminate the residual error at the lock-in frequency. A bias stability of 5.2×10-4 rad/s in 500 seconds is demonstrated experimentally.
Improving Long-Term Stability of a Resonant Micro-Optic Gyro by Reducing Polarization Fluctuation

Huilian Ma,Yuchao Yan,Yan Chen,Zhonghe Jin

DOI: https://doi.org/10.1109/JPHOT.2012.2232908

2012-01-01

Abstract:Resonant micro-optic gyros (RMOGs) with waveguide-type ring resonators are promising candidates for applications demanding small, light, and robust gyros. However, the nonzero bias at the gyro output fluctuates in terms of both the bias and the bias stability, owing to the temperature variations of the waveguide-type resonator. In particular, the temperature sensitivity of the bias stability varies greatly depending on the temperature. This paper intends to reveal that these observed fluctuations arise from the temperature-dependent polarization fluctuation. We will investigate how such polarization fluctuation affects the bias of the gyro-output through the state of polarization of the input beam, the polarization characteristics of the resonator coupler, and the temperature variation of the resonator. Both our numerical simulation and experimental verification are carried out, which, for the first time to our best knowledge, demonstrate that the long-term stability of the RMOG can be significantly improved by optimizing the temperature of the waveguide resonator.

Resonator micro-optic gyroscope based on the double phase modulation technique

Polarization maintaining silica waveguide resonator optic gyro using double phase modulation technique.

Double Closed-Loop Resonant Micro Optic Gyro Using Hybrid Digital Phase Modulation.

A Hollow-Core Photonic-Crystal Fiber-Optic Gyroscope Based on a Parallel Double-Ring Resonator.

Performance of Closed-Loop Resonant Micro Optic Gyro with Hybrid Digital Phase Modulation

Open-loop Operation Experiments in a Resonator Fiber-Optic Gyro Using the Phase Modulation Spectroscopy Technique.

Synchronous In-Phase and Quadrature Demodulation Technique for Resonant Micro-Optic Gyroscope.

Waveguide-type Optical Passive Ring Resonator Gyro Using Phase Modulation Spectroscopy Technique

Resonator micro optic gyro with double phase modulation technique using an FPGA-based digital processor

Improving thermal stability of a closed-loop resonant fiber-optic gyroscope using a double demodulation technique

Resonant fiber optic gyroscope using a reciprocal modulation and double demodulation technique

Resonant Fiber Optic Gyro Based on A Sinusoidal Wave Modulation and Square Wave Demodulation Technique

Synchronous Digital Quadrature Demodulation Technique For Resonant Optic Gyroscopes

Signal processing improvement of passive resonant fiber optic gyroscope using a reciprocal modulation-demodulation technique

Single-Polarization Fiber-Pigtailed High-Finesse Silica Waveguide Ring Resonator for A Resonant Micro-Optic Gyroscope

High Finesse Silica Waveguide Ring Resonators for Resonant Micro-Optic Gyroscopes

Resonator Fiber Optic Gyro Using the Triangle Wave Phase Modulation Technique

Polarization error in resonant micro-optic gyroscopewith different waveguide-type ring resonatorstructures

Resonator Fiber Optic Gyroscope with an All Digitalized System

Improving Long-Term Stability of a Resonant Micro-Optic Gyro by Reducing Polarization Fluctuation