Abstract:Purpose The purpose of this paper is to investigate the influence of silver nanoparticle additions on the wetting properties of Sn‐Ag‐Cu (SAC) solder paste. In this investigation, the basic solder paste contained 85 wt.% of commercial Sn 96.5 Ag 3 Cu 0.5 powder (with the particle sizes in the range of 20‐38 μ m) and 15 wt.% of self‐prepared middle activated rosin flux. To this paste was added 0.5, 1, 2 and 4 wt.% of self‐prepared silver nano‐powders of different grain sizes (from 9 to 138 nm). After the pastes had stabilized, their wetting properties were tested. The main goal of these investigations was to improve the wetting properties of SAC solder paste and to find correlations between the results of the wetting of solder paste with nanoparticles on the copper substrate with the microstructure of the solder joints. Design/methodology/approach The following methods were applied for the wetting solder paste investigation: spreading on the copper substrate, contact angle measurement on the copper and wetting on a FR‐4 laminate double sided with an 18‐ μ m thick copper foil. The investigations were performed at temperatures of 220, 230, 240 and 250°C. Cross‐sectioning was performed on the solder paste after reflow on the copper substrate. For the microstructural analysis of the “nano” modified solder joints obtained at 250°C, standard metallographic procedures were applied. Changes in the microstructure, the thickness of the inter‐metallic compounds (IMCs) and their chemical compositions were observed by means of scanning electron microscope (SEM) and energy dispersive spectroscopy (EDS). Findings As expected, a higher silver nanoparticle addition to the SAC solder paste resulted in better wetting properties on copper. The results indicated the possibility of an improvement of the reflow soldering process by using SAC solder paste with silver nanoparticles and by lowering its soldering temperature. An improvement was also observed in the wettability with a decrease in the silver nanoparticle grain size. Also, the wettability proceeded at a lower temperature (20°C lower) than that for the SAC paste, without the nano‐additives. For the 4 per cent silver nanoparticle addition, Ag 3 Sn star‐like IMCs were also found, which grew with the lowering of the silver nanoparticle grain size. Research limitations/implications Further studies are necessary for confirmation of the practical application, especially of the mechanical properties, as well as the reliability properties of the solder joints, for the chosen solder paste with silver nanoparticles. Practical implications Taking into account the wetting data, the best results of the “nano” SAC solder pastes were obtained for the highest addition of the silver nanoparticles. It was found that the spreading on copper was higher and the contact angles were lower for the SAC solder paste with 4 per cent (by wt.) of 138‐nm grain size silver nanoparticles. A comparison of SAC solder pastes with a 4 per cent silver nanoparticle addition but of a different grain size (138‐9 nm), suggested a further improvement in wetting properties with lowering of the silver nanoparticle grain size. The results suggested the possibility of an improvement in the reflow soldering process by using SAC solder paste with silver nanoparticles and by lowering its soldering temperature. Originality/value Spreading, wetting and contact angle measurement methods were used for the wetting determination of the SAC solder paste with the silver nanoparticles on copper under the same temperature conditions. Also, the microstructure of the solder joints obtained at 250°C was determined with the use of SEM and EDS methods. The results obtained made it possible to draw conclusions regarding the correlation between the output of the wetting results and the amount and the grain size of the added silver nanoparticles, and also the microstructure and thickness of the IMCs of the “nano” solder joints.

Wetting kinetics of SiC nanoparticle reinforced Sn-Pb eutectic solders

Influences of silicon carbide nanowires’ addition on IMC growth behavior of pure Sn solder during solid–liquid diffusion

Wetting Behaviors and Interfacial Reaction Between Sn-10Sb-5Cu High Temperature Lead-free Solder and Cu Substrate

Influence of doping Si 3 N 4 nanoparticles on the properties and microstructure of Sn58Bi solder for connecting Cu substrate

Silver nanoparticles effect on the wettability of Sn‐Ag‐Cu solder pastes and solder joints microstructure on copper

Soldering of Passive Components Using Sn Nanoparticle Reinforced Solder Paste: Influence on Microstructure and Joint Strength

Wettability and Shear Strength of SAC305 Based Composite Solder with Co-Doping X (ni or Al2O3) and CNTs Reinforcements

Wettability and Rheological Behavior of Low Ag Lead-Free SAC/Graphene and Cobalt-Graphene Nanocomposite Solder Paste

Influence of Al2O3 Nanoparticles on the Morphology and Growth Kinetics of Cu-Sn Intermetallic Compounds in Sn-Ag-Zn/Cu Solder Joints

Reactive Wetting of Eutectic Sn3.8Ag0.7Cu Solder on Electrodeposited Fe-Ni Alloy Layer

Comprehensive analysis of Sn58Bi/Cu solder joints reinforced with Mg particles: Wettability, thermal, mechanics, and microstructural characterization

Liquid-state interfacial reaction of Sn-10Sb-5Cu high temperature lead-free solder and Cu substrate

Study on the properties of low silver Sn1.0Ag0.5Cu composite solder reinforced with nickel-plated zinc oxide and its soldering joint

Dynamic wetting and spreading mechanisms of SAC305 with added Au elements in the laser jet weld ball bonding process

Effects of Nanoscale Cu 6 Sn 5 Particles Addition on Microstructure and Properties of SnBi Solder Alloys

In-situ fusion process and Cu–Sn compounds evolution mechanism of nano-intermetallic compound mixed solder joints

Microstructure and kinetic analysis of the properties and behavior of nickel (Ni) nano-particle doped tin–zinc–bismuth (Sn–8Zn–3Bi) solders on immersion silver (Ag)-plated copper (Cu) substrates

Effect of Ni-CNTs on Wetting Properties, Microstructure, and Creep Resistance of Sn58Bi-0.1Er Composite Solder

Determination of Reactive Wetting Properties of Sn, Sn–Cu, Sn–Ag, and Sn–Pb Alloys Using a Wetting Balance Technique

Microstructure evolution and grain refinement of ultrasonic-assisted soldering joint by using Ni foam reinforced Sn composite solder

Performance and interfacial reaction mechanism of nano-IMC-mixed solder paste with variable melting point