Abstract:Sn-Sb alloys are potential solders for replacement of high-Pb solders because of their high melting temperature in lead-free solders. However, Cu substrate is extremely dissolved by the Sn-Sb binary alloy during the high temperature soldering process, which will cause serious reliability problem of the solder joint. Based on this critical issue, we designed a new high temperature lead-free Sn-10Sn-5Cu ternary solder to prevent the dissolution of Cu substrate. In this study, liquid-state interfacial reaction between the high temperature lead-free solder and the Cu substrate was investigated. The liquid-state interfacial reaction of the solder on the Cu substrate was carried out at the different temperature of 280degC, 320degC,360degC and 400degC, and the reaction time was 1min, 10mins, 30mins and 60mins, respectively. Microstructure of the Sn-Sb-Cu bulk solder and the solder joint was observed by scattered electron microscope (SEM). The identification of phase composition was determined by Energy Dispersive X-ray Detector (EDX) and electron probe microscopy analysis (EPMA). During the four reaction temperatures, the interfacial reaction products included a scallop Cu6Sn5 intermetallic compound (IMC) layer and a flat Cu3Sn layer adjacent to Cu substrate. IMCs thickness with the reaction time was measured by the area of interface IMCs layer divided by the interface length. The IMCs thickness increased with the reaction temperature and reaction time, and the relationship between IMC thickness and reaction time was linear with square root of time, which signified that the IMC growth dynamics was diffusion controlled. The diffusion coefficient was calculated by the IMC growth rate, which increased with the higher temperature, corresponding to be 2.30 times 10-14, 6.84 times 10-14, 1.63 times 10-13, 1.99 times 10-13 m2/s for the temperatures of 280degC, 320degC, 360degC and 400degC, res- - pectively. And then the diffusion activation energy was determined to be 57.8 KJ/mol by fitting the four diffusion coefficients at various temperatures, which indicated that the diffusion mechanism was grain boundary diffusion. Between lower temperature of 280degC and higher temperature of 400degC, huge differences existed on the microstructure of IMC in the interior solder of the solder joint.

Reactive Wetting of Eutectic Sn3.8Ag0.7Cu Solder on Electrodeposited Fe-Ni Alloy Layer

Effects of High-Temperature Treatment on the Reaction Between Sn-3%Ag-0.5%Cu Solder and Sputtered Ni-V Film on Ferrite Substrate

Wetting Behaviors and Interfacial Reaction Between Sn-10Sb-5Cu High Temperature Lead-free Solder and Cu Substrate

Determination of Reactive Wetting Properties of Sn, Sn–Cu, Sn–Ag, and Sn–Pb Alloys Using a Wetting Balance Technique

Dissolution and Interfacial Reactions of Fe in Molten Sn-Cu and Sn-Pb Solders

Wetting and Interfacial Chemistry of New Pb-Free Sn-Zn-Ag-Al-Li (SZAAL) Solder with Cu, Ni, and Al Substrates

A Comparative Study of Reactive Wetting of Lead and Lead-Free Solders on Cu and (Cu 6 Sn 5 /Cu 3 Sn)/Cu Substrates

Reactive Spreading and Dewetting of Liquid SnPb Solder on Cu Thin Films

A Comparative Study of Reactive Wetting of Lead and Lead-Free Solders on Cu and (Cu<sub>6</sub>Sn<sub>5</sub>/Cu<sub>3</sub>Sn)/Cu Substrates

Wetting Behavior and Interfacial Characteristics in the Molten Bi-Sn/High-Entropy Alloy System

Effect of deposition potential on electrodeposition of Sn-Ag-Cu ternary alloy solderable coating in deep eutectic solvent

The Influence of Reflowing Process on Electrodeposited Sn-Cu-Ni Lead-Free Solder Alloy

Investigation of Interfacial Reaction Between Eutectic Sn–Pb Solder Droplet and Au/Ni/Cu Pad

Interface Reaction between Tin Solder and Nanocrystalline Ni and Ni-Mo Coatings Obtained by Electrodeposition

Wetting kinetics of SiC nanoparticle reinforced Sn-Pb eutectic solders

Interfacial Reaction of Sn–2.0Ag–2.5Zn Solder on Cu and Ni–W Substrates

Wetting Kinetics of Eutectic Lead and Lead-Free Solders: Spreading over the Cu Surface

Reactive Wetting of Tic-Ni Cermet by Ag-Cu-Zn Alloy During Evaporation

Reaction of solder with Ni/Au metallization for electronic packages during reflow soldering

Study on the metallurgical reaction law and mechanism of the Ni-xCu alloys/pure Sn solid-liquid interface

Liquid-state interfacial reaction of Sn-10Sb-5Cu high temperature lead-free solder and Cu substrate