Abstract:Due to the poor wettability of the AgCuTi alloy on the SiO2f/SiO2 composite, direct brazing of the composite with an Invar alloy could hardly achieve a reliable joint. To overcome that, the SiO2f/SiO2 composite was decorated with few-layer graphene (FLG) by a plasma enhanced chemical vapor deposition (PECVD) method. Sessile drop experiments indicate that the contact angle dropped from 123.8° to 50.7° after FLG was grown on the surface of the SiO2f/SiO2 composite. Afterwards, the effects of brazing temperature and Ti contents on the microstructure evolution and mechanical properties of joints (Invar/SiO2f–SiO2 modified with FLG) were investigated. The typical interface structure of the joint is SiO2f–SiO2/Ti5Si3+TiO2+CuxTi6−xO(x=2,3)/Ag(s,s)+Cu(s,s)+Cu–Ti blocks/wave-like Fe2Ti+Ni3Ti/Ag(s,s)+Cu(s,s)+Fe2Ti+Ni3Ti blocks/Invar. As the brazing temperature and Ti contents increase, the reaction layer on the SiO2f/SiO2 side becomes thicker and cracks gradually propagate. Meanwhile, a few dispersive Fe2Ti+Ni3Ti phases change into large-area wave-like compounds and more Cu–Ti compounds form with the increase of the Ti content. The microstructure evolution significantly affects the shear strength of the brazed joints. The highest shear strength is 26MPa brazed at 860°C for 10min with 4.5wt.% Ti content.

Active cement added brazing of quartz fibers reinforced silica composites to Invar alloy

Brazing of micrograin-filled quartz fiber reinforced silica composites and Invar using Ag-21Cu-4.5Ti alloy

Interfacial microstructure and mechanical properties of joining electroless nickel plated quartz fibers reinforced silica composite to Invar

Brazing of SiO2f/SiO2 Composite to Invar Using a Graphene-Modified Cu-23Ti Braze Filler

Brazing of SiO 2f /SiO 2 composite modified with few-layer graphene and Invar using AgCuTi alloy

Active Brazed Invar-SiO2f/SiO2 Joint Using a Low-Expansion Composite Interlayer

Interfacial Microstructure and Mechanical Property of SiO2-BN Ceramics and Invar Joint Brazed with Ag–Cu–Ti Active Filler Metal

Brazing SiO2f/SiO2 Composite to Invar Alloy Using a Novel TiO2 Particle-Modified Composite Braze Filler

Microstructure and mechanical response of the SiO2f/SiO2 composite and Invar alloy joints brazed with an AgCuTi alloy

Microstructure and Mechanical Properties of Invar Alloy and Si3N4 Ceramic Brazed Joints

Brazing continuous carbon fiber reinforced Li 2 O–Al 2 O 3 –SiO 2 ceramic matrix composites to Ti–6Al–4V alloy using Ag–Cu–Ti active filler metal

Vacuum brazing of nickel-plated quartz fiber reinforced SiO_2 composites and Invar

Vacuum Brazing ZSCf Composite Ceramics to TC4 Alloy with Ag-Cu Filler

Controlling the Intermetallics Growth in the SiO2-BN/Invar Brazed Joint by Vertical Few-Layer Graphene

Brazing of SiC Ceramics Pretreated by Chromium Coating Using Inactive AgCu Filler Metal

Interlayer design to control interfacial microstructure and improve mechanical properties of active brazed Invar/SiO2-BN joint

Joining Si3N4 ceramic to Invar using Mo mesh and Cu foil interlayer

SiC fiber strengthened Si-14Ti high-temperature filler alloy for brazing SiCf/SiC and C/C composites

Pre-infiltration and brazing behaviors of Cf/C composites with high temperature Ti Si eutectic alloy

SiC fiber strengthened Si 14Ti high-temperature filler alloy for brazing SiC f /SiC and C/C composites

Wetting and brazing of Cf/C composites with Si–Zr eutectic alloys: The formation of nano- and coarse-SiC reaction layers