Abstract:In order to improve the performance of WC based steel bonded carbide, the effects of Ni3Al content on microstructure and properties of WC-Fe(Cr, Mo) steel bonded carbide were explored based on thermodynamic calculation. The alloys with different Ni3Al contents (0, 0.5%, 1.0%, 1.4%, mass fraction) were prepared by liquid phase sintering method through adding Al with the form of Ni3Al prealloyed powders. The liquidus temperature, phase composition and microstructure of alloys were analyzed by the differential scanning calorimetry (DSC), X-ray diffractometer (XRD), scanning electron microscope (SEM) and metalloscope, respectively. The effects of Ni3Al content on the mechanical and magnetic properties of alloys were investigated. The results show that, with the increase of Ni3Al content, γ-Fe content increase, due to the improved stabilities of austenite through the solution of Ni element. The driving force for the nucleation of the γ-binder precipitating from liquid phase at 1250 ℃ increases, which refines the grains, NiAl precipitation in the binder phase increases. The hard phases are mainly WC and Fe3W3C, with the increase of Ni3Al content, more C element dissolves in γ-Fe binder phase, which leads to a less precipitation of Fe3W3C, refined WC grains are distributed more dispersedly. Above all, with the increase of Ni3Al content, the density of alloys decreases slightly. The magnetic saturation of binder phase decreases while coercive force increases. The hardness of alloys raises while the transverse rupture strength of alloys first decreases, then increases. Both the hardness and transverse rupture strength reach maximum value when the Ni3Al content is 1.4%.

Effects of Nano-Al2O3 Additions on Microstructures and Properties of WC-8Co Hard Metals

Influences of Ni/Cu/Cr3C2 Composite Additive on Microstructure and Properties of WC–10Co Fine Grained Hardmetal

Enhanced the Mechanical Properties and Corrosion Resistance of Ultra-Coarse Grain WC-8Co Cemented Carbides by the Introduction of Cu and Ni

Effects of Nano-Al2o3 and Nano-Zro2 on the Microstructure, Behavior and Abrasive Wear Resistance of WC-8Co Cemented Carbide

Effects of nano-alumina on mechanical properties and wear resistance of WC-8Co cemented carbide by spark plasma sintering

Effect of Ultra-fine WC Particles on Microstructural Evolution and Wear Behavior of Ni-Based Nano-CeO2 Coatings Produced by Laser

Effects of Ni3Al content on microstructure and properties of WC based steel bonded carbide

Effect of Nano-AlN Addition on the Microstructure and Mechanical Properties of Binderless WC-VC-TaC-AlN Cemented Carbides

Effects of Ni Addition and Cyclic Sintering on Microstructure and Mechanical Properties of Coarse Grained WC–10Co Cemented Carbides

Effect of nano-Al2O3 addition on microstructure and mechanical properties of Ti2AlNb-based composites prepared by powder metallurgy

Fabrication and Mechanical Properties of Wc-Co-Al2o3 Nanocomposites by Spark Plasma Sintering

Effect of Mo and Co additions on the microstructure and properties of WC-TiC-Ni cemented carbides

WC-Co Cemented Carbides Modified by Nano-sized Rare Earth Oxides

Cutting Performance of Wc-Co Alloys Modified by Nano-Additives

Effects of Cubic Carbides and La Additions on WC Grain Morphology, Hardness and Toughness of WC–Co Alloys

Mechanical Properties and Microstructure of Al_2O_3/WC - 8co Nanometer/micron Composites

Effect of Vc and Nbc Additions on Microstructure and Properties of Ultrafine Wc-10co Cemented Carbides

Effects of micro/nano CeO2 on the microstructure and properties of WC-10Co cemented carbides

Effects of Ni on the Microstructures and Properties of WC–6Co Cemented Carbides Fabricated by WC–6(Co, Ni) Composite Powders

Effect of Al Addition on the Microstructure and Mechanical Properties of Al x CrCoNi Medium Entropy Alloys Prepared via the Magnetron Co‐Sputtering

Ultrafine Binderless WC-based Cemented Carbides with Varied Amounts of AlN Nano-Powder Fabricated by Spark Plasma Sintering