Abstract:This article presents a novel and feasible approach for researching the quantity of the ceramic phase and component optimization in high-temperature titanium alloys with small trace amounts of ceramic phases. Different near-α titanium alloys with varying yttrium and boron contents were prepared through the utilization of a vacuum non-consumable arc furnace melting method. The alloy used was a Ti-5.9Al-4Sn-3.9Zr-3.8Mo-0.4Si base. Its microstructure, texture, mechanical properties, and fracture behavior were studied. The observation of the as-cast structure shows that the addition of different doses of trace Y and B elements significantly refines both the original β grains and α grains. Moreover, the addition of the B element transforms the Widmanstätten structure in the titanium alloy structure into a basketweave structure. The addition of Y can refine the grain structure, improve the uniformity of the matrix structure, and act as a strong deoxidizer, which will take away the oxygen in the matrix and purify it. The TiB whiskers generated with the addition of B promotes dynamic recrystallization behavior and leads to more equiaxed α grains being precipitated around them, resulting in a significant refinement of the microstructure of the as-cast alloy. After adding a small amount of B, the texture strength of the α phase is significantly reduced, indicating that TiB whiskers inhibit the formation of texture. After conducting performance screening and structure analysis, the study supplements the analysis of Y’s regulation of the titanium alloy structure. The regulation is primarily explained by combining the results of the analysis of boron content, phase diagram analysis, mechanical properties, and fracture analysis. The mechanical analysis introduces the unique load transfer strengthening of TiB whiskers combined with an analysis of high-temperature mechanical properties, as the threshold for addition. The optimal amounts of Y and B additions are 0.6 wt% and 0.8 wt%, respectively. The optimized alloy obtained under this condition can achieve a tensile strength of 950 Mpa at 500 °C without any plastic deformation or heat treatment.

CLUSTER--PLUS--GLUE--ATOM MODEL AND COMPOSITION DESIGN OF BCC Ti--Mo--Nb--Zr SOLID SOLUTION ALLOYS WITH LOW YOUNG'S MODULUS

First principles study of low Young's modulus Ti–Nb–Zr alloy system

Cluster-formula-embedded machine learning for design of multicomponent β-Ti alloys with low Young’s modulus

Study of low-modulus biomedical β Ti–Nb–Zr alloys based on single-crystal elastic constants modeling

First-principles calculations for development of low elastic modulus Ti alloys

Single crystal shear moduli of β-phase stabilized by thermomechanical treatment in TiNbSn alloys with ultralow elastic modulus

Effect of Trace Boron Addition on the Microstructural Evolution and Mechanical Properties in Ti45al8nb2cr-B Alloys

Achieving high strength in dual-phase Ti-6.4Al-4.4Mo-2.1Zr-0.6Si alloy using cluster formula design

Novel as-cast Ti-rich refractory complex concentrated alloys with superior tensile properties

Formation of coherent BCC/B2 microstructure and mechanical properties of Al–Ti–Zr–Nb–Ta–Cr/Mo light-weight refractory high-entropy alloys

Low Young’s Modulus Ti–Nb–O with High Strength and Good Plasticity

Solution Strengthening of Ductile Refractory HfMo X NbTaTiZr High-Entropy Alloys

Composition design for Laves phase-related body-centered cubic-V solid solution alloys with large hydrogen storage capacities

Investigation on the Optimal Amount of Y and B Elements in High-Temperature Titanium Alloy Ti-5.9Al-4Sn-3.9Zr-3.8Mo-0.4Si-xY-yB

High entropy six-component solid solution (Ti0.5Nb0.15Zr0.1Mo0.1Ta0.1W0.05)2AlC: A novel synthesis approach and its mechanical properties

Crystal structure and bonding characteristics of transformation products of bcc β in Ti-Mo alloys

Improved mechanical properties of W-Zr-Ti-Nb alloys via adding Ti and Nb

Recently synthesized (Zr1-xTix)2AlC (0 - x - 1) solid solutions: Theoretical study of the effects of M mixing on physical properties

Influence of Nb and Mo Contents on Phase Stability and Elastic Property of Β-Type Ti-X Alloys

Crystal Structure, Transformation Strain, and Superelastic Property of Ti–Nb–Zr and Ti–Nb–Ta Alloys