Abstract:The phase transformations during thermomechanical processing can be employed to optimize mechanical properties of β-type Ti alloys. However, such understandings are still lacking for the alloy consisting of dual β + α″ phases in solution-treated and quenched state. In this paper, the phase transformations in a Ti38Nb model alloy subjected to different thermomechanical processing were investigated by using synchrotron X-ray diffraction (SXRD) experiments, and their influence on the Young's modulus was discussed. The results indicated that high-density dislocations introduced by cold rolling still existed after annealing at temperatures lower than 573 K, which can decrease the martensitic transformation start temperature to below room temperature. With annealing temperatures increasing, the α″ → β, β → ωiso, and β → α phase transformations occurred successively. At annealing temperature of 473 K, the specimen consisted of a trace of α″ and ω phases as well as dominant β phase which was kept to room temperature by the high density of dislocations, rather than by the chemical stabilization. As a result, an ultralow Young's modulus of 25.9 GPa was realized. Our investigation not only provides in-depth understandings of the phase transformations during thermomechanical processing of β-type Ti alloys, but also sheds light on designing biomedical Ti alloys with ultralow Young's modulus.<h3 class="a-plus-plus">Graphic abstract</h3><h3 class="a-plus-plus">抽象</h3> β钛合金在热机械处理过程中的相变可以用来优化其机械性能。然而对于固溶态为β + α″的双相合金, 其相变和性能关系的研究尚且缺乏。本文利用同步辐射X射线技术研究了Ti38Nb合金在不同热机械处理状态下的相组成, 并讨论了其对杨氏模量的影响规律。结果表明冷轧引入的高密度位错在低于573 K退火后仍然存在, 这可以将马氏体相变点降至室温以下。随退火温度的升高, α″ → β, β → ωiso和β → α相变依次发生。当退火温度为473 K时, 样品中主要由β相组成并含有少量α″和ω相。这其中β相是通过高密度位错保留至室温而非化学成分稳定化。因此合金可以实现25.9 GPa的超低杨氏模量。本研究不但对β钛合金在热机械处理过程中的相变行为提供了深入理解, 而且为超低杨氏模量生物医用钛合金的开发提供了新思路.

Single crystal shear moduli of β-phase stabilized by thermomechanical treatment in TiNbSn alloys with ultralow elastic modulus

Origin of ultralow Young׳s modulus in a metastable β-type Ti-33Nb-4Sn alloy

Study of low-modulus biomedical β Ti–Nb–Zr alloys based on single-crystal elastic constants modeling

First principles study of low Young's modulus Ti–Nb–Zr alloy system

Peculiar elastic behavior of Ti–Nb–Ta–Zr single crystals

First-principles calculations for development of low elastic modulus Ti alloys

Integration of CALPHAD calculations and nanoindentation test for the design of low-modulus near-β titanium

First Principles Studies on the Elastic, Thermodynamic Properties and Electronic Structure of Ti15−xMoxSn Compounds

In-situ Investigation Via High Energy X-ray Diffraction of Stress-Induced(0002)α→(110)β Transformation in a Ti-5.5Mo-7.2Al-4.5Zr-2.6Sn-2.1Cr Alloy

Synchrotron X-ray diffraction characterization of phase transformations during thermomechanical processing of a Ti38Nb alloy

First-Principles Study on Free Energy and Elastic Properties of Disordered Β-Ti1-xnbx Alloy: Comparison Between SQS and CPA

Microstructure, mechanical properties, and cytotoxicity of low Young’s modulus Ti–Nb–Fe–Sn alloys

Tuning temperature coefficient of elastic modulus by heat treatment in a compositionally-modulated Ti-Nb-based alloy

Factors influencing the elastic moduli, reversible strains and hysteresis loops in martensitic Ti-Nb alloys

Influence of Nb and Mo Contents on Phase Stability and Elastic Property of Β-Type Ti-X Alloys

Zero thermal expansion and high Young's modulus in Ti-Nb achieved by concurrent α′′ iso and ω precipitation

Mechanical properties and deformation mechanisms of Ti-15 Nb-5Zr-4Sn-1Fe alloy with varying α phase fraction

Composition/Phase Structure and Properties of Titanium-Niobium Alloys

Phase transformations and mechanical properties of a Ti36Nb5Zr alloy subjected to thermomechanical treatments

Analysis of Mechanical-Thermal Coupled Experiments of Single Crystal TiNi Alloys

Cyclic deformation response and strain-induced martensitic transformation of β single phase Ti-35421 alloy