Abstract:The present study investigated the effect of cooling rate on the microstructure and mechanical properties of sand casting Mg–10Gd–3Y–0.5Zr alloy with a cooling rate range of 0.7–3.6°C/s. When the cooling rate was increased, the average grain size of α-Mg decreased from 59μm to 39μm, the volume fraction of the second phase increased from 17.6% to 24.5%, and the eutectic compound exhibited continuous network instead of coarsening discontinuous network of plate-shaped microstructure. Energy-dispersive X-ray test results suggested that solute content of RE elements (Gd and Y) was low within the area near the grain boundary of α-Mg with high cooling rate, and solid-solution reaction occurred in the sand casting process. In addition, Vickers hardness (HV) testing indicated that HV increased with the increasing cooling rate, and the volume fraction of second phase (V) played a main role in hardness of the alloys. There was a linear relationship between them, the fitting function was HV=1.25V+63.05, R2=0.9989. Tensile strength test showed that both of ultimate tensile strength (UTS) and tensile yield strength (TYS) first increased and then decreased with the increasing cooling rate. Based on fracture observations, the types of fracture surface characteristics are correspondingly classified into three modes, transgranular, dimple-like fracture and intergranular fracture with the increasing cooling rate.

Effect of Pour Mode and Cooling Rate on Morphologies of Mg2Si in AZ91-0.45Si Magnesium Alloy

Influence of pouring temperature on solidification behavior, microstructure and mechanical properties of sand-cast Mg-10Gd-3Y-0.4Zr alloy

Effects of Ca and Si Compound Alloying on Microstructure of AZ31 Magnesium Alloy

Effects of Cooling Rates on the Solidification Process of Al-Si-Mg Alloy

Effect of Si on Microstructure of Spray Formed AZ91 Mg Alloy

Effect of pouring temperature on thixotropic microstructure formation of AZ91

The Effect of Cooling Rate on the Microstructure and Mechanical Properties of Mg–Zn–Gd-based Alloys

Effect of cooling rate on the microstructure and mechanical properties of sand-casting Mg-10Gd-3Y-0.5Zr magnesium alloy

Influence of cooling rate on microstructure and solution behavior of Mg-Gd-Y-Zr alloy

Influence of Varied Mg/Si Mass Ratio on the Microstructure and Mechanical Properties of Aluminum Die Casting Alloys

Effect of Pouring Temperatures on the Microstructure of the Semi-Solid AlSi9Mg Alloy

Effect of Direct Chill Casting Process Parameters on the Microstructure and Macrosegregation of Mg-Al-Zn Ingot

Influence of Solution Treatment on Microstructure and Properties of In-Situ Mg_2Si/AZ91D Composites

Effect of Cooling Rate on Solidification Parameters and Microstructure of Al-7Si-0.3Mg-0.15Fe Alloy

Regulative Effect of Mg/Si Ratio on Microstructure Evolution and Mechanical Properties of Cast Al-Li-Mg-Si Alloys

Effect of Pouring Temperature During a Novel Solid–liquid Compound Casting Process on Microstructure and Mechanical Properties of AZ91D Magnesium Alloy Parts with Arc-Sprayed Aluminum Coatings

Effect of cooling rate on microstructure and mechanical properties of Mg-9Gd-4Y-1Zn-1Al alloy

Effect of Cooling Rate on the Solidified Microstructure of Mg-Gd-Y-Zr Alloy

Effect of melt overheating, cooling and solidification rates on Al–16wt.%Si alloy structure

Effects of Si content on microstructure and mechanical properties of Mg-Gd-Y-Zr casting alloy

Effects of silicon on microstructure, fluidity mechanical properties, and fracture behaviour of Mg-6Alalloy