Abstract:The solidification path of alloy reveals the detailed relationship between the solute concentration in liquid and the temperature during the solidification process. The best and most accurate method to predict the solidification path of multicomponent/multiphase alloys is to establish proper microsegregation modeling coupled with phase diagram calculations according to the CALPHAD method. Recently, several alloy systems such as Al-Cu, Al-Mg and Cu-Mg have been developed, which have aroused the interest of many researchers. Up to now, the research about Al-Cu-Mg ternary alloy, especially containing higher Mg content, is relatively rare. The purpose of the present work is to investigate the solidification path of Al-6.32Cu-25.13Mg (mass fraction, %) ternary eutectic alloy at different cooling rates and solid back diffusion coefficients by an extended unified microsegregation model coupled with Thermo-Calc. Solidification experiments and subsequent microstructural characterization are combined with numerical calculation of solidification paths. It was shown that the cooling rates R-f had no obvious effect on the solidification path which was (L+alpha)->(L+alpha+T)->(L+alpha+beta+T); but the solid back diffusion coefficient 0 had a great effect on the solidification path, which evolved gradually from (L+alpha)->(L+alpha+T)->(L+alpha+beta+T) into (L+alpha)->(L+alpha+T) when Phi increased from 0 to 1. The volume fractions of primary alpha phase V-alpha, binary eutectic V-2E and ternary eutectic V-3E at each solidification path were calculated. It was shown that V2E decreased with the increase of R-f whereas V-3E increased and V-alpha was almost invariant. The dependence of V-2E, V-3E and R-f were determined by linear regression analysis given as: V-2E=-2.51gR(f)+64.9, V-3E=2.51gR(f)-F22.12. The increase in Phi led to increases in V-alpha and V-2E and decrease in V-3E. The predicted solidification paths and volume fractions of A1-6.32Cu-25.13Mg ternary eutectic alloy at different cooling rates were in good agreement with experimental results.

Dependence of Phase Selection on Cooling Rates in As-Cast Al-Si-Mg Alloys

Effects of Cooling Rates on the Solidification Process of Al-Si-Mg Alloy

Phase Field Simulation for Non-Isothermal Solidification of Multicomponent Alloys Coupled with Thermodynamics Database

Effect of Cooling Rate on Solidification Parameters and Microstructure of Al-7Si-0.3Mg-0.15Fe Alloy

Phase Selection and Morphological Evolution for a Dilute Al-Mg-Si Alloy Under Sub-Rapid Solidification

Phase-field Study for the Influence of Solute Interactions on Solidification Process in Multicomponent Alloys

Phase Selection During Solidification of Undercooled Ni 70.2 Si 29.8 Eutectic Alloy

Phase-field Simulation of Effect of Phase-field Parameters on Solidification Process of Multicomponent Alloys

Effects of cooling rates on precipitates in homogenized Al–Cu–Li alloy

Effect of Cooling Rates on the Microstructure and Mechanical Property of La Modified Al7SiMg Alloys Processed by Gravity Die Casting and Semi-Solid Die Casting

Solidification Behavior of Ni-based Superalloy at Different Cooling Rates

Effect of Microstructure on the Precipitation of β-Mg2Si during Cooling after Homogenisation of Al-Mg-Si Alloys

Microstructure Evolution and Mechanical Properties of a Cast and Heat-Treated Al–Li–Cu–Mg Alloy: Effect of Cooling Rate During Casting

Prediction of the Solidification Path of Al-6.32cu-25.13mg Alloy by A Unified Microsegregation Model Coupled with Thermo-Calc

Relationship of Compositions, Phase Constituents and Solidification Paths of Casting Mg-Al-Zn Alloys

Influence of heat treatment on morphology and quantity of eutectic phases of Al alloys with different cooling rates

SOLIDIFICATION PHASE SELECTION IN DIRECTION-ALLY SOLIDIFIED Ti–(44%—54%)Al ALLOYS

The Effect of Cooling Rate on the Microstructure and Mechanical Properties of Mg–Zn–Gd-based Alloys

Microstructural evolution and mechanical property of Al–Mg–Mn alloys with various solidification cooling rates

Effect of Cooling Rate on Microstructure and Mechanical Properties of an Al-5.0Mg-3.0Zn-1.0Cu Cast Alloy

The influence of cooling rate and manganese content on the β-Al5FeSi phase formation and mechanical properties of Al–Si-based alloys