Abstract:Through the comparative analysis of the quality and residual wall thickness distribution characteristics of SSGAIM specimen and SSWAIM specimen, the influence law and mechanism would be explored, aiming to provide theoretical basis and guideline recommendations for the development of SSFAIM process. Based on the self‐assisted injection experimental platform, experimental studies on gas‐assisted injection molding (GAIM), and water‐assisted injection molding (WAIM) of 2 curved pipe fittings by adopting short‐shot method were carried out. UDF model was constructed for numerical simulation analysis. The influence rules of auxiliary medium and bending angle on the terminal morphology, inner wall surface quality at bending angle, medial and lateral residual wall thickness, variation range, and residual wall thickness deviation rate of short‐shot fluid assisted injection molding (SSFAIM) bending samples were compared. Meanwhile, the influence mechanism was investigated. The following experimental findings were obtained. SSFAIM had secondary penetration, while water produced multiple penetrations. There are multiple vacuum shrinkage pores in the unpenetrated area at the end of the SSWAIM sample, as well as serious shrinkage depressions on the surface. The shape of the penetration front of water is arc‐shaped with many penetration holes. The shape of the penetration front of the gas at the end of the SSGAIM sample is "pointy." Compared with the SSWAIM sample, the residual wall thickness of SSGAIM has a narrow distribution range when the bending angle is 0°. With the increase of the bending angle, the "foaming" phenomenon of the inner wall surface quality at the bending angle of the SSGAIM sample becomes less and less obvious. Moreover, the deviation of the inner and outer residual wall thickness of SSGAIM is more obvious than that of SSWAIM due to the increase of bending angle.

The MPI 3D-Simulation and Experiment of the Gas Penetration Behavior During Gas-Assisted Injection-Molding

Simulation and Experimental Analysis on Non-circular Cross-section Parts Residual Wall Thickness of Water-assisted Injection Molding

Effect on Residual Wall Thickness of Parts with Floating Core Injection of Water-Assisted Injection Molding

Gas Injection Test of Remolded Saturated Soil with Consolidation

Effects of Processing Method and Parameters on the Wall Thickness of Gas-Projectile-Assisted Injection Molding Pipes

Effect of gas on the polymer temperature in external gas-assisted injection molding

Optimization of the gas-assisted injection moulding process using multiple gas-injection systems

Factors Affecting the Stability of Gas Penetration in Gas Assist Injection Molded Bifurcation Parts

Numerical Simulation on the Penetration Behavior of the Projectile during the Water Injection Stage of Water-Projectile-Assisted Injection Molding Process

Influence of gas counter pressure injection molding parameters on shrinkage ratio of plastic part

Influence of Gas Inlet Slit Width on Gas-Assisted Plastic Micro-Tube Extrusion

Research on the Gas-assisted Injection Molding of the Box Shape Plastic Parts Based on 2.5D Numerical Simulation

Effective fast-response pressure control for thin-wall gas-assisted injection molding

Effect of Gas Counter Pressure on the Surface Roughness, Morphology, and Tensile Strength between Microcellular and Conventional Injection-Molded PP Parts

Experimental and numerical investigations on formation mechanisms of hollow structures in overflow water‐assisted injection‐molded parts of short‐glass‐fiber‐reinforced polypropylene

Experimental analysis of fluid‐assisted injection molding of pipe fittings with different angles by short‐shot method

Dimensional Analysis Theory and Molecular Dynamics Simulation of Polypropylene Melt Flow during Injection Molding Process

Formation mechanism of high‐pressure water penetration induced fiber orientation in overflow water‐assisted injection molded short glass fiber‐reinforced polypropylene

Reducing the Burn Marks on Injection-Molded Parts by External Gas-Assisted Injection Molding

An integrated simulation method for analyzing mechanical properties of injection molded fiber‐reinforced polymers

The study of short‐shot water‐assisted injection molding of short glass fiber reinforced polypropylene