Abstract:Synthesis of nanocomposites is challenging due to the difficulties in achieving homogeneous distribution of reinforcing particles in metal. In this paper, an in‐situ Al‐MgAl2O4 nanocomposite billet was prepared by the reaction of ɣ‐Al2O3 with molten Al and ultrasonication‐assisted impeller mixing. The microstructure of the composite showed homogeneously distributed MgAl2O4 crystals alongside their clusters in the Al matrix. Microstructural analysis revealed MgAl2O4 crystals distributed from 20 nm to 4 μm in size. The hardness was found to vary within the composite from 50 Hv for the matrix to 140 Hv for particle cluster regions. The grain size was reduced from 1000 μm in reference metal (CP Al) to 100 μm in the composite. The compression strength of the composite was increased substantially and higher strain hardening effect in comparison with Al was noticed in the compression test. The signatures of extensive plastic deformation such as dislocation pileups, deformed grains, grain boundary pinning etc. were observed in the composite via transmission electron microscopy. Damping properties of as‐cast composite were higher than those of CP Al in the temperature range from room temperature to 350 °C. After rolling the composite up to 40% reduction, the damping capacity (Tanδ) of the composite was found to increase marginally after 150 °C. Higher damping was found to reoccur after the annealing treatment of the composite. The improvement in damping capacity at RT was possibly influenced by the micron sized MgAl2O4 and at higher temperatures by the nano‐sized MgAl2O4 crystals. The reoccurrence of higher damping in the annealed composite underlined the stability of finer grains due to the grain boundary pinning by nano‐sized MgAl2O4 crystals. The studies on the damping property of the composite displayed the benefits of having dual size distribution of MgAl2O4 crystals (nm and μm) in the composite. This article is protected by copyright. All rights reserved.

Influence of ultrasonic processing on nano-sized particle dispersion in magnesium matrix nanocomposites

Effects of High Intensity Ultrasonic Processing on Preparation of SiC Nano-Particles Reinforced Magnesium Matrix Composite

Effect of Ultrasonic Intensification on Synthesis of Nano-Sized Particles with an Impinging Jet Reactor

Micro Pin Extrusion of Metallic Materials Assisted by Ultrasonic Vibration

Preparation of MgAl2O4-Coated Al2O3np and Migration of Ceramic Nanoparticles during Ultrasonic Processing of Aluminum Matrix Composites

Microstructural Evolution in Graphene Nanoplatelets Reinforced Magnesium Matrix Composites Fabricated Through Thixomolding Process

Magnesium Matrix Nanocomposites Fabricated by Ultrasonic Assisted Casting

Development of AZ91D Magnesium Alloy-Graphene Nanoplatelets Composites Using Thixomolding Process

Effects of sonication amplitude on the microstructure and mechanical properties of AZ91E magnesium alloy

Study on Suspension Graft Polymerization of MMA onto Nano-sized Basic Magnesium Chloride Whisker Surface in Methanol/Water Disperse Medium

The Influence of High Temperature Ultrasonic Processing Time on the Microstructure and Mechanical Properties AZ91E Magnesium Alloy

Microstructure Characteristics of A356 Nanocomposites Manufactured via Ultrasonic Cavitation Processing Under Controlled Solidification Conditions

Damping capacity of magnesium matrix composites fabricated by ultrasonic-assisted stir casting

Effects of Ultrasonic Treatment on Grain Refinement and Gas Removal in Magnesium Alloys

Fabrication and Mechanical Properties of Mesoporous Silica Nanoparticles Reinforced Magnesium Matrix Composite

Ultrasonic Processing of Magnesium Alloy for Property Enhancement

Nano-Enhanced Phase Reinforced Magnesium Matrix Composites: A Review of the Matrix, Reinforcement, Interface Design, Properties and Potential Applications

The Influence of Nanoparticles on Dendritic Grain Growth in Mg Alloys

Magnesium and magnesium alloy dissolution by high intensity focused ultrasound: erosion/cavitation vs. Wave propagation

Microstructural evolution and property evaluation of in‐situ Al‐MgAl2O4 nanocomposite prepared by ɣ‐Al2O3 and ultrasonication‐assisted impeller mixing

Study of the influence of microwave sintering parameters on the mechanical behaviour of magnesium-based metal matrix composite