Abstract:Wire crimping, a process commonly used in the automotive industry, is a solderless method for establishing electrical and mechanical connections between wire strands and terminals. The complexity of predicting the final shape of a crimped terminal and the imperative to minimize production costs indicate the use of advanced numerical methods. Such an approach requires a reliable phenomenological elasto-plastic constitutive model in which material behavior during the forming process is described. Copper alloy sheets, known for their ductility and strength, are commonly selected as terminal materials. Generally, sheet metals exhibit significant anisotropy in mechanical properties, and this phenomenon has not been sufficiently investigated experimentally for copper alloy sheets. Furthermore, the wire crimping process is conducted at higher velocities; therefore, the influence of the strain rate on the terminal material behavior has to be known. In this paper, the influence of the strain rate on the anisotropic elasto-plastic behavior of the copper alloy sheet CuFe2P is experimentally investigated. Tensile tests with strain rates of 0.0002 s−1, 0.2 s−1, 1 s−1, and 5.65 s−1 were conducted on sheet specimens with orientations of 0°, 45°, and 90° to the rolling direction. The influence of the strain rate on the orientation dependences of the stress–strain curve, elastic modulus, tensile strength, elongation, and Lankford coefficient was determined. Furthermore, the breaking angle at fracture and the inelastic heat fraction were determined for each considered specimen orientation. The considered experimental data were obtained by capturing the loading process using infrared thermography and digital image correlation techniques.

INVESTIGATION ON ANISOTROPY OF DYNAMIC COMPRESSIVE MECHANICAL PROPERTIES OF COLD-ROLLED Cu SHEET

Tensile and Compressive Deformation Behaviors of Commercially Pure Al Processed by Equal-Channel Angular Pressing with Different Dies

Tensile Deformation and Fracture Behaviours of Cold Rolled Cu-3wt.%Ag-0.5wt.%Zr Thin Sheets with Different Annealed Microstructures

An investigation of the combined size and rate effects on the mechanical responses of FCC metals

Anisotropy Study of Thin Metallic Sheets with Strain Measurement of Digital Speckle Correlation

Dynamic Compressive Mechanical Behavior and Microstructure Evolution of Rolled Fe-28Mn-10Al-1.2C Low-density Steel

Effect of Annealing on the Microstructure, Texture and Tensile Deformation Properties of Cu–3 Wt%ag–0.5 Wt%zr Thin Sheets Rolled at Room and Cryogenic Temperature

Investigation on Anisotropic Mechanical Behavior of Ti-6Al-4V Alloy Via Schmid Factor and Kernel Average Misorientation Distribution

Investigation on the Sheet Metal Anisotropy by the Plane Strain Compression Method with Laminated Samples

Experimental and numerical investigation of combined isotropic-kinematic hardening behavior of sheet metals

Strain Rate and Anisotropic Effects on Incipient Plastic Deformation of Zn–Cu–Ti Alloy Sheets

Microstructure and Bending Properties of Cu-Cr-Zr Alloy Subjected to Heat Treatment and Rolling

Study into Quasi-Static Compressive Properties of W-Cu Alloy

Effect of Cyclic Warm-Rolling Technique on Mechanical Properties of MoCu30 Thin Plates with Heterogeneous Structure

Experimental Investigation of Strain Rate Influence on Anisotropy of Uniaxial Tensile Mechanical Properties of CuFe2P Alloy Sheet

Effects of Cold Rolling Path on Recrystallization Behavior and Mechanical Properties of Pure Copper During Annealing

Anisotropy in Mechanical Properties During Microscale Uniaxial Tensile Deformation of Cu/Ni Clad Foils

Effect of annealing temperature on anisotropy of mechanical properties in powder metallurgy FeCoCrNiN0.07 high-entropy alloy sheets

Microstructure and Properties of Cold Rolled Cu80Fe20 Alloys

Anisotropic Tensile Behavior and Related Yield Point Phenomena in Annealed Ultrafine-Grained Pure Aluminum

An Investigation on Rolling Texture Transition in Copper Preprocessed by Equal Channel Angular Pressing