Abstract:Porous Si3N4 ceramics with bimodal hierarchical pore structures were fabricated through combining aqueous gelcasting and adding pore–forming agent method wherein a low–toxic monomer N, N–dimethylacrylamide (DMAA) and spherical pore–forming agent polystyrene sphere (PS) were respectively applied. The results demonstrated that PS size and content played an important function in regulating microstructure and properties of slurries, green and sintered bodies. The slurry viscosity increased sharply with the introduction of fine PS and reached a maximum of 1.78 Pa⋅s when adopting 7 wt% PS with d50 = 2.51 μm. Fine PS addition caused higher porosity in green bodies than coarse one, resulting in a significant reduction in bending strength from 28.50 MPa to 11.50 MPa, however, overall, demonstrating high enough strength for mechanical processing. The formed spherical pores from PS in ceramic matrix facilitated high porosity and highly crosslinked microstructure, thus contributing to lowering dielectric constant and loss. With PS size increasing, the dominant role in mechanical properties was transferred from porosity to microstructure, whilst dielectric properties were merely controlled by porosity and spherical pores. The porosity, bending strength, fracture toughness, dielectric constant and loss at 15 GHz varied in ranges of 36.34–52.91%, 258.42–101.21 MPa, 6.02–3.38 MPa⋅m1/2, 4.29–2.98 and 1.48–1.18 × 10−3, respectively, displaying an excellent comprehensive properties.

INFLUENCES OF FABRICATION PROCESS ON DIELECTRIC PROPERTIES OF POROUS SILICON NITRIDE CERAMICS

EFFECT OF SINTERING AID ON MECHANICAL AND DIELECTRIC PROPERTIES OF POROUS SILICON NITRIDE CERAMICS

Effects of pore structures on the dielectric properties of silicon nitride-based ceramics

A comparative study on dielectric and mechanical properties of porous β-Si3N4 ceramics by controlling porosity and microstructure

Effects of Pore Morphology on the Fabrication and Mechanical Properties of Porous Si<sub>3</sub>N<sub>4</sub> Ceramics

Microstructure, Mechanical and Dielectric Properties of Highly Porous Silicon Nitride Ceramics Produced by a New Water-Based Freeze Casting

Effects of Pore Morphology on the Fabrication and Mechanical Properties of Porous Si3N4 Ceramics

Mechanical and Dielectric Properties of Porous Si3N4–SiC(BN) Ceramic

Mechanical and Dielectric Properties of Porous Si3n4-Sio2 Composite Ceramics

Numerical and Experimental Studies of the Pore Size Impacts on Dielectric and Mechanical Properties for Porous Si <sub>3</sub>N <sub>4</sub> for Radome Application

Effect Of Porosity On Mechanical And Dielectric Properties Of 20%Bn/Si3n4 Composite Porous Ceramics

Fabrication and Properties of Porous Si3N4 Ceramic with High Porosity

Effects of α-Si3N4 seeds on properties of porous laminated silicon nitride ceramics

Effect of Si<sub>3</sub>N<sub>4</sub> Nanowires on the Mechanical Properties and Dielectric Constant of Porous Si<sub>3</sub>N<sub>4</sub> Ceramics

Comparison of Mechanical Properties of Silicon Nitrides with Controlled Porosities Produced by Different Fabrication Routes

Mechanical and dielectric properties of porous and wave-transparent Si3N4-Si3N4 composite ceramics fabricated by 3D printing combined with chemical vapor infiltration

Effect of Sintering Additive Content on Mechanical and Dielectric Properties of Porous Si3N4/BN Composite Ceramics

Effect of Chemical Vapor Infiltration of Si3n4 on the Mechanical and Dielectric Properties of Porous Si3n4 Ceramic Fabricated by A Technique Combining 3-D Printing and Pressureless Sintering

Porous Si3N4 ceramics with hierarchical pore structures prepared by gelcasting using DMAA as gelling agent and PS as pore–forming agent

Fabrication And Properties Of Porous Si3n4-Sio2 Ceramics With Dense Surface And Gradient Pore Distribution