Abstract:In the recent decades, there has been an increasing interest in preparing novel polymeric blending materials with combined and additional characteristics of each component. Having a relatively high modulus, toughness and strength, low creep, and good temperature resistance, nylons have been widely applied in the automotive industry, machinery, electronic equipment, and military applications [1]. It is well-known that blends consisting of nylon and elastomer possess excellent toughness; however, due to its highly polar amide end-groups, nylon is incompatible with elastomer. In general, it is believed that functionalization of the elastomer is a preferred approach to enhance the interfacial properties between these polymers. Research concerning nylon/functionalized elastomer blends has mostly focused on the aspects of mechanical and thermal properties. To our knowledge, only a few reports have dealt with dynamic rheological behavior of their melts [2–4]. The rheological measurements not only give much useful information for material moulding and processing, but also is an important way to characterize the structure and properties of polymer materials [5, 6]. The aim of this article is to study the influence of the graft reaction between nylon1212 and SEBS-gMA on dynamic rheological behavior and morphology of their blends. Nylon1212 (melt-flow index = 22.43 g/min) used here was obtained from Shandong Dongchen Engineering Plastic Co., Ltd., China. The elastomer, a triblock copolymer styrene-b-(ethylene-co-butylene)-b-styrene (SEBS 4033) was supplied by the Yuyao Huiju Polymer Co., Ltd. China. The maleated triblock copolymer styrene-b-(ethylene-co-butylenes)-b-styrene (SEBS-gMA) was supplied by Yuyao Yongcheng Engineering plastics Co., Ltd., China. The grafting ratio of maleic anhydride is 1.84 wt%. Both SEBS and SEBSg-MA consist of 30 wt% polystyrene end-blocks. The nylon1212/SEBS blends and nylon1212/SEBS-g-MA blends including 1 wt% antioxidant (1010) were prepared in a corotating twin-screw extruder (PRISM TES 16TC, UK) at 210 ◦C. All the samples were compression-moulded into disks of 25 mm in diameter and 1.2 mm in thickness at 180 ◦C, 50 MPa. Melt rheological tests were conducted in an ARES Rheometer

Effect of EVM/EVA-g-MAH ratio on the structure and properties of nylon 1010 blends

Effect of Polymer-Grafted Carbon Nanofibers and Nanotubes on the Interlaminar Shear Strength and Flexural Strength of Carbon Fiber/epoxy Multiscale Composites

Preparation of PBT/POE‐g‐GMA/PP Ternary Blends with Good Rigidity–toughness Balance by Core–shell Particles

Synergistic effect of EVA-GMA and nanofillers on mechanical and dielectric properties of polyamide

The dynamic rheological behavior and morphology of nylon/elastomer blends

Rheological characterization and morphology of nylon 1212/functional elastomer blends

Morphology, rheology, and mechanical properties of polylactide/ poly(ethylene-co-octene) blends

Effect of Ethylene/butyl methacrylate/Glycidyl Methacrylate Terpolymer on toughness and biodegradation of poly (l-lactic acid)

The Linear Viscoelastic Behaviors of Nylon1212 Blends Toughened with Elastomer

Super toughed poly (lactic acid)/poly (ethylene vinyl acetate) blends compatibilized by ethylene-methyl acrylate-glycidyl methacrylate copolymer

Effect of compatibilizer and polyhedral oligomeric silsesquioxane on mechanical, thermal, and morphological properties of polyamide6/poly (ethylene-co-vinyl acetate) composites

Study on the Structure and Properties of PA6/POE-g-MAH Blends

Morphologies, interfacial interaction and mechanical performance of super-tough nanostructured PK/PA6 blends

Comparison Among Three Different Approaches to Dynamic Damage Measurement for Polymer Blends

The influence of extrusion process on micromorphology of PA 6/POE/POE-g-MA ternary blends: A quantitative analysis

Influence of Crosslinking on Crystallization, Rheological, and Mechanical Behaviors of High Density Polyethylene/ethylene‐vinyl Acetate Copolymer Blends

IMPROVEMENT OF TOUGHENING AND MECHANICAL PROPERTIES EQUILIBRIUM FOR PA6/VERSIFY BLENDS BY VERSIFY-g-(MAH-co-St)

MORPHOLOGICAL EVOLUTION AND VISCOELASTIC BEHAVIOR OF COMPATIBILIZED HDPE/PA6 BLENDS

Dynamic and static mechanical properties of PP/EVA blend nanocomposites: Effects of type of masterbatch preparation technique and nature of compatibilizer

Structure And Properties Of Nanocomposites Prepared By Directly Melt Blending Ethylene-Co-Vinylacetate And Natural Montmorillonite

Combined effects of matrix molecular weight and crystallinity on the impact toughness of PP/EPR blends: The role of chain entanglement