Abstract:Multi-phase compatibilizers are potentially attractive, not only for the preparation of ternary or multi-phase immiscible polymer blends with high performance, but also for recycling and reuse of waste plastics mixture. In this study, the maleic anhydride (MAH) and styrene (St) dual monomers grafted PP, PP-g-(MAH-co-St) is prepared as a multi-phase compatibilizer, which exhibits highly effective compatibility on the PP/PA6/SEBS (70/15/15) ternary blends. Scanning electron microscopy (SEM) reveals that, with increasing the compatibilizer, the morphology evolves from the individual PA6 particle encapsulated by SEBS to several smaller-size PA6 particles partially encapsulated by SEBS phase, then to the tiny PA6 particles and some larger-size SEBS agglomerates predominantly dispersed separately in PP matrix. The morphology development predicted by spreading coefficients shows a consummate consistency with that observed by SEM. Moreover, the good compatibilization and corresponding morphologies result in superior enhancement of mechanical properties. Compared to the uncompatibilized blend, adding 15 wt multi-phase compatibilizer to the blend leads to the best mechanical properties with the yield stress, stress at break, strain at break and impact failure energy improved significantly by 23%, 132%, 647% and 220%, respectively. The results verify that the domains with small-size PA6 particles (03-0.4 mu m) partially encapsulated by SEBS (0.5-0.7 mu m) in PP matrix are very effective to enhance the mechanical properties of the blends. The morphologies of large-size PA6 particles encapsulated by SEBS or tiny PA6 particles and some larger-size SEBS agglomerates dispersed separately in PP matrix for the enhancement in mechanical properties of the blends are very limited. Consequently, the enhanced interfacial interactions and the morphology with the rigid particles partially encapsulated by a rubber-like phase in matrix are crucial for the ternary polymer.blends. (C) 2016 Elsevier Ltd. All rights reserved.

Morphology and Mechanical Properties of Polymer Blends of PBT and ABS Compatibilized by Styrene-Maleic Anhydride——The Influence of Blending Procedure

MORPHOLOGY AND MECHANICAL PROPERTIES OF NYLON-6/ABS POLYMER BLENDS COMPATIBILIZED BY STYRENE-MALEIC ANHYDIDE COPOLYMER

Morphology and Mechanical Properties of Nylon 6/PBT Blends Compatibilized with Styrene/Maleic Anhydride Copolymer

Study on the Structure and Properties of ABS/PA6/SMA Blends

Compatibilization Study of SMA and Compositional Effects on ABS/PET Blends

Research on effect of ABS,MAH,DCP on property of PA6/ABS blend

Effect of Compatibilizer on the Mechanical Property and Morphostructure of ABS/PBT Blends

Compatibility and Thermal Properties of Poly(acrylonitrile–butadiene–styrene) Copolymer Blends with Poly(methyl Methacrylate) and Poly(styrene‐co‐acrylonitrile)

Influence of Epoxy Resin on the Morphological and Rheological Properties of PBT/ABS Blends Compatibilized by ASMA

Effect of Styrene-Maleic Anhydride Copolymer on Properties of PBST/PLA Blends

Preparation of Super Toughened PA 6/ABS Blend

The Effect of Blending Sequence on Phase Morphology of Nylon 6/abs/sma Blends

Preparation and Characterization of Polyoxymethlene/Thermoplastic Polyamide Elastomer Blends Compatibilized by Maleic Anhydride Grafted ABS Copolymer

Morphology and Mechanical Properties of Blends of Thermoplastic Polyurethane and Polyolefins

Influence of Methyl Methacrylate-Co-glycidyl Methacrylate Copolymers on the Compatibility, Morphology and Mechanical Properties of Poly(butylene Terephthalate) and Polycarbonate Blends

Compatibilization of poly(2,6-dimethyl-1,4-phenylene oxide)/polyamide 6 blends with styrene-maleic anhydride copolymer: Mechanical properties, morphology, crystallization, and melting behavior

Creating Super-Tough and Strong PA6/ABS Blends Using Multi-Phase Compatibilizers

Investigation of the Properties of PBT/ABS-g-GMA Blends Modified with Epoxy Resin of Mid-Molecular Weights

Effect of Abs Grafting Degree and Compatibilization on the Properties of Pbt/Abs Blends

Morphology Development and Superior Mechanical Properties of Pp/Pa6/Sebs Ternary Blends Compatibilized by Using A Highly Efficient Multi-Phase Compatibilizer

Influences of component ratio of minor phases and charge sequence on the morphology and mechanical properties of PP/PS/PA6 ternary blends