Abstract:Tensile, compressive, cyclic tension-tension, and cyclic compression-compression tests at room temperature were systematically applied to a Zr52.5Cu17.9Al10Ni14.6Ti5 bulk metallic glass for comprehensive understanding of its damage and fracture mechanisms. Under tensile loading, the metallic glass only displays elastic deformation followed by brittle shear fracture. Under compressive loading, after elastic deformation, obvious plasticity (0.5 to 0.8 pct) can be observed before the final shear fracture. The fracture strength under compression is slightly higher than that under tension. The shear fracture under compression and tension does not occur along the maximum shear stress plane. This indicates that the fracture behavior of the metallic glass does not follow the Tresca criterion. The fracture surfaces show remarkably different features, i.e., a uniform vein structure (compressive fracture) and round cores coexisting with the radiating veins (tensile fracture). Under cyclic tension-tension loading, fatigue cracks are first initiated along localized shear bands on the specimen surface, then propagated along a plane basically perpendicular to the stress axis. A surface damage layer exists under cyclic compression-compression loading. However, the final failure also exhibits a pure shear fracture feature as under uniaxial compression. The cyclic compression-compression fatigue life of the metallic glass is about a factor of 10 higher than the cyclic tension-tension fatigue life at the same stress ratio. Based on these results, the damage and fracture mechanisms of the metallic glass induced by uniaxial and cyclic loading are elucidated.

Ultrahigh Fatigue Strength in Ti-Based Bulk Metallic Glass

Fatigue Behavior of a High-Toughness Zr 61 Ti 2 Cu 25 Al 12 Bulk Metallic Glass

Fatigue Endurance Limit and Crack Growth Behavior of a High-Toughness Zr 61 Ti 2 Cu 25 Al 12 Bulk Metallic Glass

Tension-Tension Fatigue Behavior of High-Toughness Zr61Ti2Cu25Al12 Bulk Metallic Glass

Ultrasonic Fatigue of Ti&lt;sub&gt;40&lt;/sub&gt;Zr&lt;sub&gt;10&lt;/sub&gt;Cu&lt;sub&gt;34&lt;/sub&gt;Pd&lt;sub&gt;14&lt;/sub&gt;Sn&lt;sub&gt;2&lt;/sub&gt; Glassy Alloy

High-strength Cu-based bulk glassy alloys in Cu–Zr–Ti and Cu–Hf–Ti ternary systems

Compression-compression Fatigue Behavior of CuZr-based Bulk Metallic Glass Composite Containing B2 Phase

Crack-Resistance Curve of A Zr-Ti-Cu-Al Bulk Metallic Glass with Extraordinary Fracture Toughness

Cu-based bulk glassy alloys with high tensile strength of over 2000 MPa

Damage-Tolerant Zr-Cu-Al-Based Bulk Metallic Glasses with Record-Breaking Fracture Toughness

Locating bulk metallic glasses with high fracture toughness: Chemical effects and composition optimization

Achieving ultrahigh-specific strength and enhanced GFA in Ti-based bulk metallic glasses via a two-step alloying strategy

A Ti–Zr–Be–Fe–Cu Bulk Metallic Glass with Superior Glass-Forming Ability and High Specific Strength

Stress-life fatigue behavior and fracture-surface morphology of a Cu-based bulk-metallic glass

Effect of Ti addition on mechanical properties of Zr-based bulk metallic glasses

Fatigue and fracture behavior of bulk metallic glass

Glass Forming Ability and Mechanical Properties of New Ni-Based Bulk Metallic Glasses

Centimeter-sized Ti-rich Bulk Metallic Glasses with Superior Specific Strength and Corrosion Resistance

Cu-Based Bulk Glassy Alloys with Good Mechanical Properties in Cu-Zr-Hf-Ti System

Mg-based Bulk Metallic Glass Composites with Plasticity and Gigapascal Strength

The Novel Ti-based Metallic Glass with Excellent Glass Forming Ability and an Elastic Constant Dependent Glass Forming Criterion