Abstract:A major problem of utilizing co-firing technique is controllably distributing fuel mixtures of pulverized coal and granular biomass in a common pipeline. This research related into particle velocity distribution in the vertical pipe after a right angle elbow was undertaken using the Laser Doppler Anemometry (LDA) technique and a coupled computational fluid dynamics (CFD)-discrete element method (DEM) simulation. According to the similarity criterion of Stokes Number, three types of glass beads were used to model the dilute gas-solid flow of pulverized coal or biomass pellets. In the vertical pipe after an elbow (R/D=1.3, R is the bend radius as 100mm and D is pipe diameter as 75mm), a horseshoe shape feature has been found on cross-sectional distributions of the axial particle velocity for all three types of glass beads on the first section which is 15mm away from the blend exit. At the further downstream sections, the horseshoe-shaped feature is gradually distorted until it completely disappears. The distance for total disintegration is about 300mm away from the first section for the first type of glass beads, 150mm away for the second type and 75mm away for the third one. As for particle number rate, its cross-sectional distribution on the first section shows that a rope is formed at the pipe outer wall where the maximum particle number rate occurs. On the whole, the rope formed by the first type of glass beads can be still observed at the section which is 450mm away from the first section. For the second type of glass beads, the rope will disintegrate from the section (300mm away) according to the cross-sectional distributions of the dimensional value of particle axial velocity divided by air conveying velocity. Overall, the roping characteristic is not obviously shown in the gas-solid flow of the third type of glass beads after the first section. All of these indicate that ropes formed from larger particles disperse more easily, for reasons perhaps related to their higher inertia. In addition, CFD-DEM analysis was employed to determine the particle characteristics to confirm this assumption. The numerical results indicated that the flow pattern has the highest axial velocity near the elbow to form the ‘horseshoe’ pattern. As the particles with lower Stokes Number were easier to follow the air flow, this is the reason why the horseshoe pattern of smaller particles was more obvious than larger particles.

Experimental investigation into the performance of pulverized-coal splitter with an elbow using fiber optic probe

Experimental Measurements of Gas–solid Flow and Splitting Mechanisms of a Coal Pipe Splitter with a Perpendicularly Arranged Upstream Elbow

Experimental Investigations on the Performance of a Coal Pipe Splitter for a 1000 MW Utility Boiler: Influence of the Vertical Pipe Length

Particle Velocity Measurements in Transition Section of Turbulent Fluidized Beds Using Optical Fiber Probe and CFD Simulation

Experimental Investigations on Performance of Collision-Block-Type Concentrator Using Fiber Optic Probe

Experimental and Numerical Study of Particle Velocity Distribution in the Vertical Pipe after a 90° Elbow

Measurement on the Pulverized Coal Concentration after a Combination of Two Elbows Using Method of Optic Fluctuation Theory

Effect of elbow structure on gas-so lid separation and flow field adjacent to the exit of the swirl burner

Measurement of Characteristics of Solid Flow in the Cyclone Separators with Fiber Optical Probe

Experimental investigations on performance of collision-block-type fuel-rich/lean burner: Influence of solid concentration

A SIMULATION STUDY ON THE SEPARATING PERFORMANCE OF AN IMPACT TYPE FUEL RICH-LEAN BURNER AFFECTED BY THE ELBOWS

Distributed Optical Measurement System for Plate Fin Heat Exchanger

Investigation of the impact of splitter blades on a low specific speed pump for fluid-induced vibration

Model simulation and experimental research of acoustic-plane installation angle of multi-path ultrasonic gas flowmeter

Simulation Study on Composite Structure of Impact Type Fuel Rich-lean Burner and Elbows

Experimental Measurements of a Gas–solid Jet Downstream of a Fuel-Rich/lean Burner with a Collision-Block-type Concentrator

Simulation and experiment investigation on effect of upstream pipe single elbow on the performance characteristics of V-Cone flowmeters

Experimental Study on Spontaneous Combustion Monitoring in Coal Mine Airspace Based on Distributed Fiber Optic Temperature Measurement

EXPERIMENTIAL INVESTIGATION OF DISTRIBUTION OF VOID FRACTION BETWEEN HORIZONTAL TUBE BUNDLE

CFD–DEM investigation of gas-solid flow and wall erosion of vortex elbows conveying coarse particles

Experimental Investigation on Local Particle Volume Fractions Distribution in Offset-Exit Circulating Fluidized Bed