Abstract:The transition section between bottom dense zone and top dilute zone is important for fast gas-solids catalytic reactions,such as methanol to olefins(MTO).Solids concentration and fluctuation parameters in the transition section of a fluidized bed with 95 mm i.d.were measured by using reflective optical fiber probe(PV6D).The influences of superficial gas velocity and static bed height were investigated.An Eulerian-Eulerian two-fluid model that incorporated kinetic theory of granular flow and modified three-zone drag law was used to predict the flow structure in the turbulent fluidized bed.The axial and radial distributions of solids concentration were simulated by means of computational fluid dynamics(CFD).The experiments showed two axial profiles of solids distribution in the transition section:exponential and S-shaped.The maximum gradients of both axial and radial solids concentration profiles were located in the transition section,which meant that solids distribution in the transition section was much more non-uniform than that in the dilute and dense sections.The change of gas velocity and static bed height would cause a shift between exponential and S-shaped profiles,and significantly affect solids concentration in the dense region near the wall and at the bottom.Probability density distribution of local solids concentration revealed that when static bed height was small,the location of maximum voidage would gradually move from core region to annular region with increasing gas velocity,resulting in a bimodal distribution of voidage.A modified three-zone drag model was proposed by taking the effect of particle clustering into account for CFD simulation.The simulated solids concentration distribution agreed well with experimental data in the transition section except for the distributor zone.

Experimental investigations on performance of collision-block-type fuel-rich/lean burner: Influence of solid concentration

Experimental Investigations on Performance of Collision-Block-Type Concentrator Using Fiber Optic Probe

Experimental Measurements of a Gas–solid Jet Downstream of a Fuel-Rich/lean Burner with a Collision-Block-type Concentrator

Experimental and Numerical Study of Solids Concentration Distribution in Transition Section of Turbulent Fluidized Bed

TEST STUDY ON OUTLET FLOW FIELD PERFORMANCE FROM WAVE-SHAPED COMBUSTION-STABILIZING BODY OF THE CONCENTRATION TUNABLE RICH/LEAN BURNERS

Numerical Simulation of the Effects of Block Height on the Gas−Solid Flow in a Fuel-Rich/Lean Burner by the Hard-Sphere Model

Two-Phase Flow Measurements of a Gas−Solid Jet Downstream of Fuel Rich/Lean Burner

Numerical Simulation on the Rich/Lean Pulverized Coal Burner

Experimental Investigation on the Flow Characteristics of Rice Husk in a Fuel-Rich/lean Burner

DEM–CFD Simulation of the Particle Dispersion in a Gas–solid Two-Phase Flow for a Fuel-Rich/lean Burner

Research on Separation Characteristics and Resistance Characteristics of Two-Phase Flow in Rich Lean Burner

A SIMULATION STUDY ON THE SEPARATING PERFORMANCE OF AN IMPACT TYPE FUEL RICH-LEAN BURNER AFFECTED BY THE ELBOWS

THE NUMERICAL INVESTIGATION ON THE TRANSIENT CHARACTERISTICS OF THE GAS-SOLID TWO-PHASE FUEL RICH-LEAN BURNER FLOW

Impact of Dilution Ratio and Burning Conditions on the Number Size Distribution and Size-Dependent Mixing State of Primary Particles from Domestic Solid Fuel Burning

Experimental Investigation on Flow Structures and Mixing Mechanisms of a Gas–solid Burner Jet

E207 USING LIGHT FLUCTURATION METHOD TO STUDY THE GAS-SOLID BURNER FLOW

Diffusion Characteristics of Colliding Rich-Lean Gas-Solid Two-Phase Flows

Investigations into the Ignition Behaviors of Pulverized Coals and Coal Blends in a Drop Tube Furnace Using Flame Monitoring Techniques

Influence of Cyclone Combustor Structure on the Motion Behaviors of Solid Fuel Particles

Experimental Investigation On The Influence Of Air Velocity On The Particle Dispersion Behavior Of Rice Husk In A Fuel-Rich/Lean

THE DIFFUSION CHARACTERISTICS OF THE HORIZONTAL FUEL RICH-LEAN GAS-SOLID BURNER FLOW