Abstract:Laser solid forming (LSF) is a newly advanced additive manufacturing technique which offers a huge potential in efficiency and cost savings for fabricating the components of aerospace titanium alloys with high performance. In this research, the macrostructure/microstructure and electrochemical dissolution features of the Ti-6Al-4V alloy produced by LSF and forging were investigated. The LSFed Ti-6Al-4V that included as-deposited and annealing heat treatment (HT) conditions contains three periodically distributed microstructural morphologies: fine microstructure zone (FMZ), coarse microstructure zone (CMZ), and layer band. All zones of the different microstructural morphology in an entire deposit are constituents of α-laths and a small amount remained in the β phase. An alternating structure of coarse and fine microstructures was observed along the deposition direction in the deposit. Layer bands are generally spaced above the CMZ. The CMZ is a constituent of a slightly coarser basket weave structure than that of the FMZ. However, the layer bands present the microstructure of colony α. Additionally, the α-laths are slightly coarsened by HT, and this simultaneously results in a more homogeneous microstructure compared with the as-deposited microstructure. Moreover, the forged Ti-6Al-4V possesses the most homogeneous microstructure and the largest size of the α phase. Simultaneously, a variety of dissolved morphology features were observed in the three types of samples after potentiodynamic polarization tests. The order of the surface macrosmooth level of these samples is forged > HT > as-deposited. For LSFed Ti-6Al-4V, the FMZs and the layer bands present a faster electrochemical dissolution rate than that of the CMZs. Consequently, the uneven surface is revealed by the distinct dissolution rate of different microstructural zones at the same LSFed sample. The forged Ti-6Al-4V alloys present a uniformly dissolved behavior, which is attributed to the homogeneity of the microstructure. The elimination of the layer bands and the homogenization of the microstructure of the LSFed Ti-6Al-4V are of great significance for improving the surface quality during electrochemical machining.

Influence of composition on microstructure and properties of Ti-Fe alloys prepared by laser-induced self-propagating reaction synthesis

Laser-induced Self-Propagating Reaction Synthesis of Ti–Fe Alloys

The Influence of Ni on Microstructure and Properties of Ti-Fe Eutectic Alloy Prepared by Laser-induced Self-propagating Reaction Synthesis

Influence of mixing enthalpy on the microstructure of laser multi-layer deposited Ti-6Al-4V alloy

Fe Element Promotes the Transformation from Columnar to Equiaxed Grains and the Formation of Ultrafine Microstructure of Ti-6Al-4V Alloy by Laser Wire Deposition

INFLUENCE OF MIXING ENTHALPY ON THE MICROSTRUCTURE OF LASER MULTILAYER DEPOSITED Ti-6Al-4V ALLOY

Chemical Composition Analysis for Laser Solid Forming of Titanium Alloys from Blended Elemental Powders

Effect of Layer Band and Heterogeneity of Microstructure on Electrochemical Dissolution of Laser Solid Formed Ti-6Al-4V Alloy

Microstructure and Properties of Ti-Fe-Zr-Y Alloys Prepared by Laser Rapid Prototyping

Fe nanoparticles modified pure Ti alloy on microstructure evolution and fine crystallization mechanism fabricated by additive manufacturing

Effect of Fe Content on Microstructures and Properties of Ti6Al4V Alloy with Combinatorial Approach

Microstructure performance and Nano-Effect of laser alloying composites with Multi-Phase on TA1 titanium alloy

Effect of Ti microalloying and laser remelting on the microstructure and mechanical properties of laser powder bed fusion Al-12Si alloy

Achieving superior strength-ductility combination in the heterogeneous microstructured Ti64 alloy via multi-eutectoid elements alloying with CoCrFeNiMn during laser powder bed fusion

Effect of Fe Addition on the Microstructure, Transformation Behaviour and Superelasticity of NiTi Alloys Fabricated by Laser Powder Bed Fusion

The Influence of Mixing Enthalpy on the Geometric Properties of Laser Solid Formed Ti-6Al-4V

Influence of Laser Ignition Power on Microstructure and Property of Amorphous-based Composite Fabricated by Laser-induced Self-propagating Reaction Synthesis

Investigation of the Influence of Fe on the Microstructure and Properties of Ti5553 Near-Β Titanium Alloy with Combinatorial Approach

The Pseudo-Eutectic Microstructure and Enhanced Properties in Laser-Cladded Hypereutectic Ti–20%Si Coatings

Effect Of Fe Content On The As-Cast Microstructures Of Ti-6al-4v-Xfe Alloys

Influence of Al and Ti Alloying and Annealing on the Microstructure and Compressive Properties of Cr-Fe-Ni Multi-Principal Element Alloy