Abstract:The use of titanium (Ti) in the additive manufacturing (AM) industry has been steadily increasing. However, iron (Fe), a significant impurity originating from the sponge production process, is difficult to remove due to high energy requirements. Consequently, fully eliminating Fe from Ti is challenging and expensive. Understanding the role of Fe in Ti alloys and determining a maximum allowable threshold for AM is therefore critical. This knowledge could potentially relax current industry standards and enable the development of more sustainable Ti alloys. This study investigated the effect of Fe on the microstructure development and mechanical properties of Ti-Fe alloys, with a focus on their suitability for additive manufacturing. Through an in-situ alloying approach, Fe content was systematically increased from 0 to 3 wt%, leading to significant grain size reduction, from over 100 μm to less than 5 μm. These modifications in grain size and morphology, achieved by adjusting the Fe content in laser-based powder bed fusion (LPBF) fabricated Ti alloys, are directly related to substantial enhancements in the mechanical properties. The hardness increased from 171 to 366 HV, and the tensile strength effectively doubled from 426 to 1026 MPa while maintaining ductility. XRD analysis revealed the presence of a full α phase when the Fe content was ≤ 0.75 wt%. However, at higher Fe concentrations, small β peaks were observed. To identify the strengthening mechanisms, theoretical frameworks such as the Hall-Petch relationship and Labusch model were employed. Two significant inflection points were identified at Fe concentrations of 0.1 % and 1 wt%, indicating three important compositional ranges: Region #1 (Fe ≤ 0.1 wt%), Region #2 (0.1–1 wt% Fe), and Region #3 (1–3 wt% Fe). The strengthening mechanism in each region is discussed in detail.

Fe Element Promotes the Transformation from Columnar to Equiaxed Grains and the Formation of Ultrafine Microstructure of Ti-6Al-4V Alloy by Laser Wire Deposition

Fe nanoparticles modified pure Ti alloy on microstructure evolution and fine crystallization mechanism fabricated by additive manufacturing

Sustainable alloy design: Fe-enhanced Ti alloys for superior mechanical performance in additive manufacturing

Effects of Fe Contents on the Microstructure and Precipitate of Ti–Al–V Alloys Prepared by Direct Energy Deposition

Additive manufacturing of titanium alloys with enhanced strength and uniform ductility via multi-element alloying

Microstructure and mechanical properties of B modified Ti-Fe alloy manufactured by casting, forging and laser melting deposition

Effect of Fe Content on Microstructures and Properties of Ti6Al4V Alloy with Combinatorial Approach

Effect of Fe Content on Microstructure Evolution and Mechanical Properties of as-cast Ti-xFe-B Alloy

Effect of Manganese on Grain Morphology and Microstructure of Ti-6Al-4V Alloy by Laser Wire Deposition

Effect Of Fe Content On The As-Cast Microstructures Of Ti-6al-4v-Xfe Alloys

Improving Microstructure and Mechanical Properties of Ti43Al5Nb0.1B Alloy by Addition of Fe

Effect of Cu-induced Eutectoid Transformation on Microstructure and Mechanical Properties of Ti–6Al–4V Alloy by Laser Wire Deposition

Hierarchical Grain Refinement During the Laser Additive Manufacturing of Ti-6Al-4V Alloys by the Addition of Micron-Sized Refractory Particles

Microstructure and Mechanical Properties of Laser Metal Deposited Ti6Al4V Alloy with Near Equiaxed Β Grain Structure

Microstructure Evolution and Grain Refinement Behavior During Hot Deformation of Fe Micro-Alloyed Ti-6Al-4V

Achieving superior strength-ductility combination in the heterogeneous microstructured Ti64 alloy via multi-eutectoid elements alloying with CoCrFeNiMn during laser powder bed fusion

Improvement of microstructure and mechanical properties of TiAl?Nb alloy by adding Fe element

Complete fine-equiaxed β-columnar grains in laser direct energy deposition of Ti–6Al–4V parts

Microstructures Analysis and Quantitative Strengthening Evaluation of Powder Metallurgy Ti–Fe Binary Extruded Alloys with (Α+β)-Dual-phase

Effects of the microstructure and texture characteristics on mechanical properties of the Al–Ni–Cu–Fe alloy manufactured by laser powder bed fusion

Influence of Ti addition on microstructure and mechanical behavior of a FCC-based Fe30Ni30Co30Mn10 alloy