Abstract:Purpose. Research of cutting force components during machining of high-hard cast iron by special prefabricated cutters with brazed niborite and ciborite inserts. Determination of the influence of geometric characteristics of the cutting tool, cutting modes and hardness of the material being machined on the cutting forces. The methods. The research methods were based on the fundamentals of cutting theory and cutting tools, material science properties of the tool and processed material. A research bench with special equipment was used. Findings. The nature of the change in the components of cutting forces with depth t, feed rate S and cutting speed v was experimentally investigated. The studies have shown an excess of the resulting force in the horizontal plane Pv over the circumferential one Pz, which is the main feature of turning high-hard metals. It has been established that the main limiting factors in the wear of tool cutting inserts are the permissible levels of forces. The hardness of HB has the greatest effect on the radial force Py. Under identical turning conditions for materials with a hardness of 220 to 610 HB, the forces Pz, Py and Px increase by 1,7; 3,3 and 2,3 times, respectively. In addition to the natural increase, the ratio of cutting forces also changes. Reducing the front angle of the blade causes a deterioration in chip formation conditions and leads to an increase in all components of the cutting forces. An increase in the radius at the top of the cutter r causes an increase in the width and decrease in the thickness of the layer to be cut, as well as a decrease in the main angle in the plan φr on the radial part of the blade. The originality. A complex dependence in the structural-stage form was obtained, which gives a clear picture of the influence of each parameter of the turning process on its performance. This dependence is a mathematical model for calculating the optimal operating and geometric parameters of the turning process of high-hard cast irons. The influence of the frontal angle γ, wear value h, and hardness of HB cast iron on the power characteristics during machining of high-hard cast irons has been studied. Practical implementation. It has been shown that it is economically advantageous to maximize the wear of cutting inserts made of relatively expensive composites. In this case, it is necessary to use a technological system of machine-workpiece-tool of high rigidity.

CUTTING FORCES IN HIGH SPEED TAPPING CAST IRON BY TUNGSTEN CARBIDE TAPS

Finite Element Simulation Of High-Speed Cutting Alloy Cast Iron

Influence of Tool Geometrical Parameters on High Speed Cutting of Titanium Alloy Ti6Al4V

Study on A Novel Adaptive Force Control Table Employed for Rotary Ultrasonic Drilling

The Finite Element Analysis Of Serrated Chip Formation In High-Speed Cuffing Auto Panel Dies

Modeling of Non-Linear Cutting Forces for Dry Orbital Drilling Process Based on Undeformed Chip Geometry

Hole Diameter Variation and Roundness in Dry Orbital Drilling of Cfrp/Ti Stacks

Experimental analysis and modeling of cutting power model

Study of cutting forces during turning of high-hard cast irons

Research and Optimization of Extrusion Tap Structure Based on Numerical Simulation and Experimental Analysis

Research on Variable Parameter Drilling Method of Ti-CFRP-Ti Laminated Stacks Based on Real-Time Sensing of Drilling Axial Force

Evaluation of Machining Parameters Affecting Cutting Forces in Dry Turning of GGG50 Ductile Cast Iron

Analysis, modelling, and optimization of force in ultra-precision hard turning of cold work hardened steel using the CBN tool

Investigation of Cutting Force in High Feed Milling of Ti6al4v

Study on Turning Force of Γ-Tial Alloy

Study of wear behavior and tool life in different taps during the internal threading of a nodular iron engine crankshaft

Cutting Performance Optimization and Experimental Research of Indexable Insert Drill

ALTERATION OF THE CUTTING FORCE COMPONENTS IN TANGENTIAL TURNING

Research on PCBN Tool Dry Cutting GCr15

Forces in Hard Turning of 51crv4 with Wiper Cutting Tool

Influences of Micro Mechanical Property and Microstructure on Performance of Machining High Chromium White Cast Iron with Cbn Tools