Abstract:The specific contact resistivity and reflectivity of Ni/Ag/Ti/Au contact with p-GaN are studied. It is found that the thickness of Ag, anneal time and deposition temperature have a great effect on the performance of Ni/Ag/Ti/Au electrode. Its optical reflectivity is measured by reflectivity spectrophotometer, and its specific contact resistivity is calculated by circular transmission line model. It is observed that the contact reflectivity values of Ni (1 nm)/Ag/Ti (100 nm)/Au (100 nm), when the thickness values of Ag are 25 nm and 50 nm, are low: their values are 68.5% and 82.1% at 450 nm, respectively, and they start to increase with increasing the Ag thickness, then reach their saturated values when Ag thickness is beyond 200 nm. When the anneal time changes from 1 min to 10 min in oxygen atmosphere, the specific contact resistivity decreases at 300 ℃, decreases further and then increases at 400-600 ℃. After annealing at temperatures at 300 ℃ and 400 ℃ in oxygen atmosphere, the contact reflectivity value of Ni/Ag/Ti/Au remains almost unchanged, even when anneal time increases from 1 min to 10 min. However, The contact reflectivity of Ni/Ag/Ti/Au decreases significantly after annealing at a temperature higher than 400 ℃ and it becomes smaller with longer annealing time. After 400 ℃ annealing in oxygen atmosphere for 3 min, the specific contact resistivity reaches 3.6×10-3 Ω·cm2. Additionally, the deposition temperature of Ni/Ag is investigated. It is noticed that the specific contact resistivity decreases and the reflectivity increases with increasing the deposition temperature from room temperature to 120 ℃. The reflectivity rises to 90.1% at 450 nm and the specific contact resistivity reaches 6.4×10-3Ω·cm2 for the Ni/Ag/Ti/Au electrode at a deposition temperature of 120 ℃. However, the effects of improving the electrical and optical characteristics weaken when deposition temperature changes from 120 ℃ to 140 ℃. With a overall consideration, Ni (1 nm)/Ag (200 nm)/Ti (100 nm)/Au (100 nm) is made at a deposition temperature of 120 ℃, and then anneals at 400 ℃ for 3 min in oxygen atmosphere to achieve the optimized electrode. The vertical light emitting diode with this Ni/Ag/Ti/Au electrode is fabricated. Its working voltage is 2.95 V and the light output power is 387.1 mW at 350 mA. The electro-optical conversion efficiency reaches 37.5%.

A Novel Ni/Ag/Pt Ohmic Contact to P-Type GaN for Flip-Chip Light-Emitting Diodes

Ni/Ag/Pt Ohmic Contacts to P-type GaN

Electrical Characteristics of Ti/Al/Ti/Au Multilayer Ohmic Contacts to N-Type GaN

Effects of Surface Treatment on Non-alloyed Ti/Al Ohmic Contact of n-GaN

Highly Reflective Ni/Ag/Pt/Au Ohmic Contacts To P-Gan With Ito Interlayer

The Reflectivity and Ohmic Contact Resistivity of Ni/Ag/Ti/Au in Contact with P-Gan

Very-low-specific-resistance Pd/Ag/Au/Ti/Au alloyed ohmic contact to p GaN for high-current devices

Ohmic Contact of High Reflectivity on P-Type GaN

The Study on the Reflectance and Resistance of Ni/Ag/Ti/Au Electrode Contact to p-GaN

Ohmic Contacts in GaN-based Devices

Research on P-Type GaN / Au Ohmic Contact

High-reflectance Ohmic Contacts to P-Gan of GaN-based Violet LEDs

Transparent (Ni,Au)/ZnO:Al-Based Ohmic Contacts to p-Type GaN as an Insight into the Role of Ni and Au in Standard p-Type GaN Contacts

Reflective Ni/Ag/Ti/Au Electrode with Low Specific Contact Resistivity

Ohmic Contact of Ti/Al/Ni/Au on N-Face GaN

Pd/In/Ni/Au Contact to N-Polar N-Type Gan Fabricated by Laser Lift-Off

The Dichotomous Role of Oxygen in the Ohmic Contact Formation on P-Type GaN Grown by MBE and MOCVD

Ohmic Contact with a Contact Resistivity of 12 Ω ⋅ Mm on P-Gan/algan/gan

Au/Ni/Au as a contact for p-Type GaAs

Oxidation Treatment on Ni/Au Ohmic Contacts to P‐type GaN

Ohmic Contact Mechanism of Ni/Au Contact to P-Type Gan Studied by Rutherford Backscattering Spectrometry