Abstract:The essential goal of this research is to evaluate the modification process on phase transformation, matrix chemical composition, and precipitated carbide types for modified SAE-AISI T1 steel and their effects on the hardness values after optimum heat treatment conditions. This research adopts the alloying design strategy to enhance one of the most important tools steel coded SAE-AISI T1 (T12001). Therefore, two alloying enhancement processes took place through partial or total tungsten replacement. Investigated steel was modified first through the addition of vanadium and then through the addition of vanadium and carbon. Substitute 5 wt modified SAE-AISI T1 steel. % tungsten with 1 wt. % vanadium, in addition to carbon content, varied from 0 to 1 wt. %. Therefore, to fulfill the goals of this work, Thermo-Calc software was utilized to get the following: (i) thermodynamic equilibrium information, (ii) the expected microstructure, (iii) the constituent volume fraction, and (iv) carbide chemical composition. The chemical composition of the expected phases was confirmed by scanning electron microscopy (SEM) equipped with energy-dispersive X-ray (EDX). In addition, volume fractions of different constituents were estimated by using Thermo-Calc software and authenticated by the imaging analysis process. The experimental findings for the variations in the chemical composition of the matrix and eutectic carbides precipitated, e.g., MC and M6C carbides, agree well with the calculated findings. Tungsten replacement by vanadium with and without extra carbon at traditional SAE-AISI T1 steel encourages MC carbide formation instead of M6C, M23C6, and M7C3 carbides. MC carbide precipitated in vanadium with extra carbon-modified steel contains more carbon, chromium, and tungsten but less vanadium compared with vanadium-modified steel. Vanadium with extra carbon-modified steel precipitated more M6C carbide and gamma-austenite. Hardness measurements emphasized that modified steel is a promising material for its use as a tooling material with low tungsten content and, in turn, produces cutting-tool materials with economical cost.

Phase Structure and Fine Microstructure of In-Situ Vanadium Carbides in Cast High-Vanadium High-Speed Steel

Fabrication and microstructure of in situ vanadium carbide ceramic particulates-reinforced iron matrix composites

Microstructural Characterization of a V2C and V8C7 Ceramic-Reinforced Fe Substrate Surface Compound Layer by EBSD and TEM

Compositional and structural characterization of alloyed carbide by 3D atom probe and high-resolution TEM

Microstructure and Formation Mechanism of Vanadium Carbide-Reinforced Iron-Matrix Composites Prepared by Solid-Phase Diffusion

Formation and evolution of primary carbides in high-carbon martensitic stainless steel

Microstructure, Microhardness and Wear Resistance of VCp/Fe Surface Composites Fabricated in Situ

Study of Microstructure of Coarse-grain Tungsten Carbide Composite Produced by In-Situ Metallurgy Reaction

Improvement in microstructure and wear-resistance of high chromium cast iron/medium carbon steel bimetal with high vanadium

Investigations of Solidification Structures of High Carbon Alloy Cast Steel Containing RE-V-Ti

Effect of Ferrite/Martensite on Microstructure Evolution and Mechanical Properties of Ultrafine Vanadium Dual-Phase Steel

Microstructure, retained austenite, and mechanical properties evaluation of Vanadis 60-HfC-Ta 0.6 Nb 0.4 C steel matrix composite by vacuum sintering, sub-zero, and heat treatments

Investigating Microstructural Evolution and Its Influence on Tribological Behaviors of In-Situ Formed VCp Reinforced Iron-Based Composites with Variable Mn Content

Microstructural Characteristics and Properties of Adding Vanadium Carbide Powders to Vanadis 4 Tool Steel Through Vacuum Sintering and Heat Treatments

Rapid Solidification Microstructure and Carbide Precipitation Behavior in Electron Beam Melted High-Speed Steel

Research Progress of Eutectic Carbides in High-Speed Steel

Effect of Alloying and Microalloying Elements on Carbides of High-Speed Steel: An Overview

Thermodynamic Calculation and Characterization of Carbide Precipitation in Laser-Deposited Material for High-Speed Steel Alloy

Microstructural Characterization of Nanostructured WC-Co Cemented Carbides

Study on the Microstructure of Vanadium-Modified Tungsten High-Speed Steel-Coded SAE-AISI T1 Steel

A modified M2 high-speed steel enhanced by in-situ synthesized core-shell MC carbides