Abstract:In this study, four kinds of heat treatments were performed to obtain a certain amount of retained austenite, which can result in good toughness and low brittleness accompanied with wear resistance of an in situ VC particle reinforced iron-based composite (VCFC). Microstructure, mechanical properties and wear resistance of the samples under heat treatment of QP, QPT, MQP and MQPT were compared. The experimental results indicated that there is a huge difference in microstructure between MQPT and the other heat treatments. High-proportion retained austenite and white net-like precipitates of M7C3 carbide existed in the MQPT-treated sample, but thick M7C3 carbide with brittleness was discovered in the other sample. Thereby, high-proportion retained austenite contributed to its low hardness of 634 HV and high tensile strength of 267 MPa, while a maximum hardness of 705.5 HV and a minimum tensile strength of 205 MPa were exhibited in the QPT-treated sample with a V-rich carbide of high hardness, a Cr-rich carbide of brittleness and a high-proportion martensite. Meanwhile, a phase transformation from retained austenite to martensite could increase the hardness and enhance wear resistance based on the transformation-induced plasticity (TRIP) effect; its wear rate was only 1.83 × 10−6 mm−3/(N·m). However, the wear rates of the samples under QP, QPT and MQP heat treatments increased by 16.4%, 44.3% and 41.0%, respectively. The wear mechanism was a synergistic effect of the adhesive wear mechanism and the abrasive wear mechanism. The adhesive wear mechanism was mainly considered in the MQPT-treated sample to reduce the wear rate attributed to high-proportion retained austenite and the existence of wear debris with a W element on the surface of the wear track. However, the abrasive wear mechanism could exist in the other samples because of a lot of thick, brittle M7C3, thereby resulting in a higher wear rate due to immediate contact between the designed material and the counterpart.

Microstructure, Microhardness and Wear Resistance of VCp/Fe Surface Composites Fabricated in Situ

Fabrication and microstructure of in situ vanadium carbide ceramic particulates-reinforced iron matrix composites

Study on Microstructure of Vanadium and Chromium-Carbide Reinforced Fe Matrix Surface Composite

Microstructure, Mechanical and Wear Properties Study of Vanadium Carbide Particles Reinforced Iron Matrix Composite

Microstructure and wear properties of in-situ TiC-Cr7C3/Fe surface composite

Microstructure and Formation Mechanism of Vanadium Carbide-Reinforced Iron-Matrix Composites Prepared by Solid-Phase Diffusion

The Correlation Analysis of Microstructure and Tribological Characteristics of In Situ VCp Reinforced Iron-Based Composite

Microstructure, Mechanical Properties, and Wear Resistance of VCp-reinforced Fe-matrix Composites Treated by Q&P Process

Microstructure and Wear Properties of in Situ TiC-Cr7C3/Fe Surface Composite

Effects of Heat Treatment on Microstructure and Mechanical Properties of In-situ VC/Fe Composites

MICROSTRUCTURE AND WEAR RESISTANCE OF CHROMIUM CARBIDE COATING IN SITU SYNTHESIZED BY VEB

Microstructure and Wear Properties of In Situ Production of (Fe,Cr)7C3 Particulate Bundles Reinforced Iron Matrix Composites

Effect of Carbide Ceramic Zone on Wear Resistance of the (fe,cr)7c3/fe Surface Gradient Composite

Research on Microstructure and Wear Resistance of (fe,cr)<sub>7</sub>c<sub>3</sub>/fe Surface Gradient Composite

In situ production of vanadium carbide particulates reinforced iron matrix surface composite by cast-sintering

Microstructure and Wear Properties of<i> In Situ </i>Production of (Fe,Cr)<sub>7</sub>C<sub>3</sub> Particulate Bundles Reinforced Iron Matrix Composites

Microstructural and Mechanical Properties of in Situ WC-Fe/Fe Composites

Investigating Microstructural Evolution and Its Influence on Tribological Behaviors of In-Situ Formed VCp Reinforced Iron-Based Composites with Variable Mn Content

Fracture Toughness of Tungsten Carbide Reinforced Fe-Matrix Surface Composites

Microstructure and Wear Resistance of Iron Matrix Composites Reinforced by In-Situ Carbides

High-temperature Oxidation Resistance of VCps-reinforced Fe-matrix Composites Using an In-Situ Reaction