Abstract:Carbon nanotube/continuous carbon fiber reinforced poly(ethylene terephthalate) (CNT/CCF/PET) composites are prepared by melt impregnating. The effects of CF and CNT content on the mechanical properties, melt and crystallization behaviors, and submicroscopic morphology of CNT/CCF/PET composites are studied. The tensile test results show that the increase of CF and the addition of appropriate amount of CNT improved the tensile strength and tensile modulus of the composites. When the content of CNT is 1.0 wt% and the content of CF is 56 wt%, the properties of the composites are the best, with tensile strength of 1728.7 MPa and tensile modulus of 25.1 GPa, which is much higher than that of traditional resin matrix composites. The results of dynamic mechanical analysis (DMA) show that the storage modulus of the composites increased with the increase of CF and CNT content. In particular, the addition of CNT greatly reduced the loss modulus of the composites. Morphological analysis show that the addition of CNT improved the fiber–matrix interface of the composite, which changes from fiber pull-out and fracture failure to fiber matrix fracture failure, and the fiber matrix interface is firmly bonded. In addition, there are polymer coated CNT protrusions on the surface of the fiber was observed. The results of differential scanning calorimetry (DSC) show that the melting temperature and crystallization temperature of the composites increased with the increase of CF content. The addition of CNT had little effect on the melting temperature of the composites, but it further improved the crystallization temperature of the composites. The effect of CNT content on the crystallization kinetics of the composites is studied. The non-isothermal crystallization kinetics of the composites is described by Jeziorny's improved Avrami equation. The results show that CNT has a great influence on the crystallization type of the composites. As a nucleating agent, CNT has obvious heterogeneous nucleation effect in the composites, which improves the crystallization rate of PET.

Fabrication And Characterization Of A New Pitch-Based Acnt/C Nanocomposites

Fabrication and Characterization of Aligned Cnt/C Composites

Carbon-nanotube-templated Carbon Nanofibers with Improved Mechanical Performance

Fabrication and structure: a study of aligned carbon nanotube/carbon nanocomposites

Studies on Thermal Conductive Properties and Mechanism of a New ACNT/C Nanocomposite Material

Microstructure of the pyrocarbon in aligned carbon nanotube/carbon composites

Study on Oxidation Properties of New ACNT/C Nanocomposites

Fabrication and mechanical properties of in situ prepared mesocarbon microbead/carbon nanotube composites

SYNTHESIS AND THE PERFORMANCE OF CARBON NANOTUBES-(Ni-P) COMPOSITES

Microstructure and mechanical properties of carbon graphite composites reinforced by carbon nanofibers

Epitaxial Grown Carbon Nanotubes Reinforced Pyrocarbon Matrix in C/C Composites with Improved Mechanical Properties

Thermal Properties of Aligned Carbon Nanotube/Carbon Nanocomposites

In situ consolidation process-based fabrication and interlaminar modification mechanism associated with CF/PEEK multiscale nanocomposites characterized by interlaminar doping of CNTs

The Fabrication And Characterization Of N-Doped Aligned Carbon Nanotube Arrays In Large Area

Mechanical and thermal conduction properties of carbon/carbon composites with different carbon matrix microstructures

Microstructural investigation and performance of carbon matrix composites developed through facile pitch modification route

Improving carbon/carbon composites mechanical and thermal properties by the co‐carbonization of pre‐oxidized carbon fiber and pitch

A Novel Continuous Carbon Nanotube Fiber/carbon Composite by Electrified Preform Heating Chemical Vapor Infiltration

Study on Mechanical Properties of Carbon Nanotube Reinforced Composites

Hexagonal Crystalline Nanofillers Reinforced Composite Carbon Nanofibers with Optimized Crystal Structure and Improved Mechanical Properties

Mechanical Properties, Melting and Crystallization Behaviors, and Morphology of Carbon Nanotubes/Continuous Carbon Fiber Reinforced Polyethylene Terephthalate Composites