Abstract:In-situ formed carbides at interface can enhance the interfacial bonding and load-transfer effect in nanocarbon/Al composites, but always sacrifice the structure integrity of reinforcement, inevitably degrading the strengthening efficiency. To alleviate such limitation, a novel hybrid leaf-like carbon nanotube (CNT)-graphene nanoribbon (GNR), architectured via partially longitudinal unzipping of multi-walled CNT (UZCNT), was adopted to reinforce Al matrix composites. Results show that the prominent mechanical properties of UZCNT/Al over CNT/Al were achieved, which originates from the in-situ formed interfacial Al4C3 together with the well-retained integrity of UZCNT. The regulated interfacial reaction between UZCNT and Al generates dense nano-sized Al4C3 (diameter: 14–19 nm, length: 36–82 nm), rather than its submicron-sized counterpart (diameter: 26–37 nm, length: 111–186 nm) with low number density which forms in unmodified CNT/Al composites. Systematic analysis indicates that the interfacial Al4C3 in UZCNT/Al forms via “nucleation-growth” pattern, contrary to the predominant epitaxial growth of Al4C3 in CNT/Al. It is revealed that UZCNT can stimulate Al4C3 nucleation via reducing the nucleation energy barrier and increasing the number of nucleation sites. Meanwhile, finite active C atoms and low-defective inner walls in UZCNT retard the fast growth of Al4C3 after nucleation. Such “nucleation-growth” pattern renders the formation of high number-density nano-sized Al4C3 at GNR margin in UZCNT/Al. Atomic-scale characterizations demonstrate that the coherent/semi-coherent Al4C3-Al interfaces in UZCNT/Al preferentially exhibit specific orientation relationships, most of which are reproducible by the edge-to-edge matching model. The present work is supposed to provide important insights on interfacial carbide formation in nanocarbon/metal composites.

Fabrication and Characterization of Aligned Cnt/C Composites

Fabrication and structure: a study of aligned carbon nanotube/carbon nanocomposites

Carbon-nanotube-templated Carbon Nanofibers with Improved Mechanical Performance

Fabrication And Characterization Of A New Pitch-Based Acnt/C Nanocomposites

Microstructure of the pyrocarbon in aligned carbon nanotube/carbon composites

Studies on Thermal Conductive Properties and Mechanism of a New ACNT/C Nanocomposite Material

The Fabrication And Characterization Of N-Doped Aligned Carbon Nanotube Arrays In Large Area

Thermal Properties of Aligned Carbon Nanotube/Carbon Nanocomposites

Processing and Mechanical Property Characterization of Aligned Carbon Nanotube Carbon Matrix Nanocomposites

Fabrication and properties of aligned multiwalled carbon nanotube-reinforced epoxy composites

Study on Oxidation Properties of New ACNT/C Nanocomposites

J2240204 Evaluation of the Properties and Alignment of Carbon Nanotube Sheet Grown by CVD Method

Formation of the orientation relationship-dependent interfacial carbide in Al matrix composite affected by architectured carbon nanotube

Full on-line preparation of polymer composites reinforced with aligned carbon nanotubes

CNT-induced heterogeneous matrix grain structure in CNTs/Al composites

A Novel Continuous Carbon Nanotube Fiber/carbon Composite by Electrified Preform Heating Chemical Vapor Infiltration

Carbon Nanotubes Grown on Graphite Films as Effective Interface Enhancement for an Aluminum Matrix Laminated Composite in Thermal Management Applications

Epitaxial Grown Carbon Nanotubes Reinforced Pyrocarbon Matrix in C/C Composites with Improved Mechanical Properties

Enhancement of thermal–mechanical performances via a selective CNTs configuration in laminated CNTs/AZ31B composite

The Fabrication of Macroscopical Long Aligned Carbon Nanotube Arrays

Carbon Nanotube/Epoxy Composites Fabricated by Resin Transfer Molding