Abstract:The Zr-ZrC-ZrC/DLC gradient composite films were prepared on TiNi alloy by the techniques combined plasma immersion ion implantation and deposition (PIIID) and plasma enhanced chemical vapor deposition (PECVD). With this method, the Zr-ZrC intermixed layers can be obtained by the ion implantation and deposition before the deposition of the ZrC/DLC composite film. In our study, an optimal gradient composite film has been deposited on the NiTi alloys by optimizing the process parameters for implantation and deposition. The surface topography was observed through AFM and the influence of the deposition voltage on the surface topography of the film was investigated. XPS results indicate that on the outmost layer, the Zr ions are mixed with the DLC film and form ZrC phase, the binding energy of C Is and the composition concentration of ZrC depend heavily on the bias voltage. With the increase of bias voltage, the content of ZrC and the ratio Of sp(3)/sp(2) firstly increases, reaching a maximum value at 200 V, and then decreases. The nano-indentation and friction experiments indicate that the gradient composite film at 200 V has a higher hardness and lower friction coefficient compared with that of the bare NiTi alloy. The microscratch curve tests indicate that gradient composite films have an excellent bonding property comparing to undoped DLC film. Based on the electrochemical measurement and ion releasing tests, we have found that the gradient composite films exhibit better corrosion resistance property and higher depression ability for the Ni ion releasing from the NiTi substrate in the Hank's solution at 37 degrees C. (C) 2007 Elsevier B.V. All rights reserved.

Deposition of DLC coating on biomedical TiNi alloys by plasma based ion implantation to improve surface properties

The corrosion behavior and hemocompatibility of TiNi alloys coated with DLC by plasma based ion implantation

Ti-TiC-TiC/DLC gradient nano-composite film on a biomedical NiTi alloy.

Influence of Negative Voltage on the Structure and Properties of DLC Films Deposited on NiTi Alloys by PBII

Diamond-Like Carbon Thin Films Deposited On Ti6al4v Alloy Surface By Plasma Gun At Atmospheric Pressure

Properties of Zr–ZrC–ZrC/DLC Gradient Films on TiNi Alloy by the PIIID Technique Combined with PECVD

Effect of C2h2 Flow Rate on the Deposition of Zr-Zrc-Zrc/Dlc Gradient Nano-Composite Film on Biomedical Niti Alloy

EFFECT OF C2H2 FLOW RATE ON THE DEPOSITION OF TI-TIC-TIC/DLC GRADIENT NANO-COMPOSITE FILM ON NITI ALLOY

Deposition of TiN coatings on shape memory NiTi alloy by plasma immersion ion implantation and deposition

Surface Characterization and Electrochemical Studies of Biomedical Niti Alloy Coated with Tin by Piiid

The Effects of Ti/Ni Doping on the Friction and Wear Properties of DLC Coatings

Formation of TiN films on biomedical NiTi shape memory alloy by PIIID

Characterisation of Ultra-Thin DLC Coatings by SEM/EDX, AFM and Electrochemical Techniques

Enhanced Corrosion Resistance of Zr Coating on Biomedical Tini Alloy Prepared by Plasma Immersion Ion Implantation and Deposition

Characterization of TiN, TiC and TiCN coatings on Ti–50.6 at.% Ni alloy deposited by PIII and deposition technique

Tantalum Coated NiTi Alloy by PIIID for Biomedical Application

Modification of Biomedical NiTi Shape Memory Alloy by TiC/Ti Films Using PIIID

The corrosion resistance and biomineralization of the DCPD-PCL coating on the surface of the additively manufactured NiTi alloy

Diamond-Like Carbon Coatings on Plasma Nitrided M2 Steel: effect of deposition parameters on adhesion properties

Diamond-like Carbon Film Synthesized by Ion Beam Assisted Deposition and Its Tribological Properties

DLC coating over pre-oxidized and textured Ti6Al4V for superior adhesion and tribo-performance of hip implant